Robomow City 120 Скачать руководство пользователя

Страница: 4 / 76

Introduction - 2

Robomow City 120

The products are manufactured by F. Robotics Acquisitions (Friendly Robotics).

CE approved.

transmitted or translated without the prior written consent of Friendly Robotics.

Product, product specifications and this document are subject to change without notice. All other trademarks are property of

their respective owners.

Welcome to the world of home robotics with the Friendly Robotics Robomow!

Thank you for purchasing our product. We know that you will enjoy the extra free time you will have while using Robomow to mow your

lawn. When set up and used properly, Robomow will operate safely on your lawn and provide you with a quality of cut matched by a

few mowers of any kind. You will be impressed with your lawn’s appearance and best of all, Robomow did it for you.

IMPORTANT!

The following pages contain important safety and operating instructions.

Please read and follow all instructions in this manual. Carefully read and

review all safety instructions, warnings and cautions contained in this manual.

Failure to read and follow these instructions, warnings and cautionary statements

may result in severe injury or death to persons and pets or damage to personal property.

Содержание City 120













































































Результаты поиска

Содержание City 120

Отзывы:

Похожие инструкции для City 120

Бренды по названию

Популярные бренды

Robomow City 120, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание City 120

Отзывы:

Похожие инструкции для City 120

Бренды по названию

Популярные бренды