Reeves G2 series Скачать руководство пользователя страница 96

Страница: 96 / 183

Operation & Maintenance w/IPB

G2 Series Decontamination Water Heater

0015

Part Number: 1006375

0015-8

DHS Systems LLC

This document contains information proprietary to DHS Systems LLC and is intended solely for use by its customers. No portion of this document may be reproduced
for release to a third party without written consent of DHS Systems LLC.

INSTALLATION OF FUEL PUMP/SOLENOID:

2. Installing the fuel pump/solenoid as follows:

a. Install fuel pump/solenoid assembly into burner motor housing.

b. Loosely thread (2) mount bolts into the fuel pump housing; do not tighten at this time.

c. Using a 7/16” open end wrench, connect and tighten the fuel nozzle tube B-nut.

d. Using a 9/16” open end wrench, connect and tighten the fuel line B-nut at the fuel pump.

e. Using a ½” open end wrench, tighten the (2) fuel pump mounting bolts.

Using a 9/16” open end wrench, connect and tighten the fuel in-line at the fuel water strainer housing.

g. Connect the solenoid electrical plug.

h. Connect power cord to power supply outlet.

Perform operations and leak checks.

END OF TASK

Содержание G2 series
























































































































































































Результаты поиска

Содержание G2 series

Отзывы:

Похожие инструкции для G2 series

Бренды по названию

Популярные бренды

Reeves G2 series, Руководство по эксплуатации

Результаты поиска

Содержание G2 series

Отзывы:

Похожие инструкции для G2 series

Бренды по названию

Популярные бренды