Reeves G2 series Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 183

background image

Operation & Maintenance w/IPB

G2 Series Decontamination Water Heater

0013

Part Number: 1006375

0013-4

DHS Systems LLC

This document contains information proprietary to DHS Systems LLC and is intended solely for use by its customers. No portion of this document may be reproduced
for release to a third party without written consent of DHS Systems LLC.

Table 1. Operator Preventive Maintenance Checks and Service (Cont).

ITEM

NO.

INTERVAL

ITEM TO BE

CHECKED

OR SERVICED

PROCEDURE

EQUIPMENT NOT

READY/

AVAILABLE IF:

GAUGES

10

3 MONTH
(TO INCLUDE
ALL BEFORE
ITEMS PLUS
THE
FOLLOWING)

Test fuel
pressure
gauge

Verify fuel pressure gauge operates
properly by authorized service technician.

Contact Reeves
EMS for service.

Test water
temperature
gauge

Verify water temperature gauge operates
properly by authorized service technician.

Contact Reeves
EMS for service.

FILTER

11

6 MONTH
(TO INCLUDE
ALL BEFORE
AND 3
MONTH
ITEMS PLUS
THE
FOLLOWING)

Fuel Filter

Fuel filter replacement required.

Remove and
replace fuel filter.

12

12 MONTH
(TO INCLUDE
ALL
BEFORE, 3
AND 6
MONTH
ITEMS PLUS
THE
FOLLOWING)

Test Voltage
and Amp Draw

Perform volt meter and amp meter readings
by an authorized service technician.

Contact Reeves
EMS for service.

Fuel Pump
Internal Filter

Inspect fuel pump internal filter by an
authorized service technician.

Contact Reeves
EMS for service.

Burner
Electrodes

Inspect and adjust proper gap requirement
by an authorized service technician.

Contact Reeves
EMS for service.

Fuel Nozzle

Fuel nozzle replacement required.

Contact Reeves
EMS for service.

Fuel Pickup In-
line Screen

Inspect and clean fuel pickup in-line screen
by an authorized service technician.

Contact Reeves
EMS for service.

«
...
62
63
64
65
66
...
»

Содержание G2 series
























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для G2 series

Бренд: Landmann Страницы: 24

Бренд: Eccotemp Страницы: 56

Бренд: Raypak Страницы: 60

Pali 9510CA-BBX

Бренд: Caframo Страницы: 5

Бренд: Calpeda Страницы: 32

Бренд: RainSoft Страницы: 16

Бренд: Zehnder Rittling Страницы: 20

Бренд: VEAB Страницы: 6

Бренд: Gasmate Страницы: 20

Бренд: Greenway Home Products Страницы: 9

Бренд: Desa Страницы: 36

Бренд: Mesa Living Страницы: 14

Бренд: EBARA Страницы: 69

Бренд: Warmtech Страницы: 21

PROTÉGÉ RPAGP

Бренд: Raypak Страницы: 3

Бренд: Kozy-World Страницы: 29

Бренд: Scarlett Страницы: 14

Elnur ECOMBI HHR Series

Бренд: Gabarron Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды