background image

General Safety Information

This manual provides information on installation, start-up and 
maintenance for a gas fired unit.  Improper installation can lead 
to unsatisfactory operation or dangerous situations. This unit 
should only be installed and maintained by qualified personnel.  
Qualified personnel should have a clear understanding of 
the contents of this manual prior to installation.  Improper 
installation may lead to electric shock, possible injury from 
contact with moving parts and/or possible burns from contact 
with heating components.  Additional safety concerns can 
arise from unit location such as a roof or inclement weather 
(outdoor installations).  Additional safety precautions may be 
required.

Installer shall follow all national and local electrical code 
requirements such as the National Electrical Code (NEC) 
and the Canadian Electrical Code (CEC) in Canada.  Where 
applicable, follow National Fire Protection Association (NFPA) 
requirements.  The appliance must be electrically grounded in 
accordance with local codes or, in the absence of local codes, 
with the National Electrical Code, ANSI/NFPA 70, and /or the 
Canadian Electrical Code, CSA C22.1, if an external electrical 
source is utilized.

The appliance installation shall conform to local building codes 
or, in the absence of local codes, with the National Fuel Gas 
Code, ANSI Z223.1/NFPA 54, or the Natural Gas and Propane 
Installation Code, CSA B149.1. 

In addition to this manual, start-up and commissioning 
videos are available at www.priceindustries.com.  Additional 
information on this unit can be found by scanning the QR code 
sticker or by contacting Price Industries.

WARNING

 

The manufacturer’s warranty does not cover any 
damage or defect caused by modifications to the 
unit including unauthorized attachments of other 
components. Such activity may lead to unsatisfactory 
performance and may endanger life and property.

NOTE: 

This document is customer property and must be 

retained by the unit’s owner for use by maintenance personnel.

Safety Notices

Throughout this manual Caution and Warning notices are used 
where additional safety information may be required.  Warnings 
are provided to alert personnel of a potential situation that 
could result in personal injury or death.  Cautions are provided 
to alert personnel of a potential situation that could result in 
personal injury.  

In addition to Warnings and Cautions, Notices are used to 
indicate a situation that may result in property damage.

WARNING

 

Indicates a potential situation that, if not avoided, could 
lead to serious personal injury or death.

CAUTION

 

Indicates a potential situation that, if not avoided, could 
lead to minor or moderate personal injury.  Cautions may 
also be used to indicate unsafe practices.

NOTICE:

 Indicates a situation or action that may cause 

damage to the unit or the facility.

1

AW-I

OVERVIEW

priceindustries.com 

  |   

AW-I - Manual

Содержание AW-I Series









































Отзывы: