background image

Limited Warranty

(a)   Price warrants and guarantees for a period limited to twelve (12) months from 

date of installation / commissioning or eighteen (18) from date of shipment - 
whichever comes first, that the Products are manufactured in accordance with 
Price’s quotation and submittal drawing specifications and of specified material 
unless otherwise expressly stated.  

(b) Price will manufacture the goods to be supplied in accordance with the product 

specifications supplied by Purchaser.  Price shall not be liable for any loss or 
damages of any kind resulting from errors, omissions or untimely notification 
of changes to the specifications that have been provided.  In the event that 
changes to the product specifications arise, Price must be notified immediately 
and in writing.  The Purchaser will assume liability for the cost of all material and 
resources, work-in-progress and finished goods that have become obsolete 
or that can no longer be used due to any such changes in the specifications 
supplied.

(c)  In the event the Products supplied do not comply with quotation and submittal 

drawing specifications and/or material quality standards within the warranty 
period, Price will either repair the Products supplied or provide replacement of 
such Products that conform to the quotation and submittal drawing specifications.  
This decision is made at the sole discretion of Price.  In either case, Price will 
not be responsible for labor and freight charges incurred in replacing Products 
except as agreed to by Price in writing, nor will Price be responsible for incidental, 
consequential or punitive damages.  In the event Price elects to repair the 
Products supplied, Purchaser will assist by providing Price with all details of the 
problem and a written quotation for the costs of such work to be carried out. If 
the repair is authorized by Price, then Purchaser will assist by coordinating and 
supervising the repair work.  In the event Price elects to replace the Products, 
Price may either (i) direct the Purchaser to return such Products to Price or (ii) 
provide replacement Products to the Purchaser without the return of the original 
Products, in which case Purchaser will be responsible for the disposal of such 
original Products.  Such election is at the sole discretion of Price, and all returns 
of Products to Price must be approved in advance by Price.  In the event Price 
directs Purchaser to return the Products to Price for repair or replacement, 
Purchaser agrees to return such Products to Price in a manner consistent with 
the original packaging in order to prevent damage.  All freight back to Price’s 
factory and return freight to Purchaser must be agreed upon prior to return of the 
Products.

(c)  Price makes no warranty whatsoever with respect to components or items 

supplied which may be warranted separately by their manufacturer.  Price does 
not warrant factory mounted controls and components of Products supplied and 
owned by a third party for mounting by Price.  Back charges to Price for Products 
under warranty by others will only be accepted if prior written approval is given by 
Price.

(d) THE WARRANTIES AND LIABILITIES SET FORTH IN THE PRIOR PARAGRAPHS 

ARE THE ONLY WARRANTIES OR LIABILITIES OF PRICE.  ALL OTHER 
GUARANTEES, WARRANTEES, CONDITIONS AND REPRESENTATIONS, 
EITHER EXPRESS OR IMPLIED, WHETHER ARISING UNDER ANY STATUTE, 
LAW, COMMERCIAL USAGE OR OTHERWISE, INCLUDING IMPLIED 
WARRANTIES FOR FITNESS OF MERCHANTIBILITY AND FITNESS FOR A 
PARTICULAR PURPOSE, ARE HEREBY EXCLUDED.  

(e)  The foregoing warranty shall not take effect unless Purchaser shall inform Price 

in writing of any flaw, defect or deficiency in the Products promptly after such 
flaw, defect or deficiency becomes apparent and, in any case, not later than 
one (1) year from date of shipment.  The warranty provided for under these 
Terms shall be void upon the following: (i) the unauthorized repair or modification 
by any person other than Price of Products claimed to be defective; or (ii) the 
improper installation, maintenance or operation of the Products other than in strict 
accordance with standard industry practices and compliance with the specific 
recommendations of Price respecting the Products; or (iii) the misuse, negligence, 
or operation of the Products other than for their intended purpose.

AW-I Standard Warranty

Heat Exchanger Warranty

Drum and tube heat exchangers on Price AW-I units are warrantied for a period 
of five years from date of shipment.  If, during this period, a heat exchanger fails 
because of a defect in manufacture or material, Price Industries will repair or replace 
the part at its discretion.  Price will not be responsible for labor and freight charges 
incurred in replacing parts.

The Price warranty is void if;

1.  The unit is not installed and serviced in accordance with 

manufacturer’s recommendations.

2.  Operation, maintenance, start-up and shut down are not in 

accordance with manufacturer’s instructions.

3.  Unit is operated in conditions not specified by the manufacturer.
4.  The unit is operated while the building is under construction.
5.  Unit is used for application which it was not intended.

AW-I Extended Warranty (Optional)

Extended Heat Exchanger Warranty

Drum and tube heat exchangers on Price AW-I units are warrantied for a period of ten 
years from date of shipment.  If, during this period, a heat exchanger fails because 
of a defect in manufacture or material, Price Industries will contribute to the cost of 
replacing the part in accordance with the following table;

Price will not be responsible for labor and freight charges incurred in replacing parts.

The Price warranty is void if;

1.  The unit is not installed and serviced in accordance with 

manufacturer’s recommendations.

2.  Operation, maintenance, start-up and shut down are not in 

accordance with manufacturer’s instructions.

3.  Unit is operated in conditions not specified by the manufacturer.
4.  The unit is operated while the building is under construction.
5.  Unit is used for application which it was not intended.

Years from manufacture

Price’s financial 

responsibility

Purchaser’s financial 

responsibility

0 – 5th year

100%

0%

6th year

100%

0%

7th year

80%

20%

8th year

60%

40%

9th year

40%

60%

10th year

20%

80%

29

AW-I

MAINTENANCE

priceindustries.com 

  |   

AW-I - Manual

Содержание AW-I Series









































Отзывы: