PlayNation Play Systems 1501 Скачать руководство пользователя | Manualshive

Страница: 167 / 189

background image

***IMPORTANT NOTICE FOR TREEHOUSE KIT PLAYSETS***

Read all instructions thoroughly before beginning construction, this is very important. The
“Treehouse Add On Kit” (1525) box will require you to deviate slightly from the standard kit
instructions.

Typical deviations include:

1) The Telescope that is usually on the front of the set on the Front face board (arched board)
must be moved to another location on the set. Additional instructions to mount the Telescope to
a 2 x 4 or a 4 x 4 are included in the play set Appendix or with the “Treehouse Add On Kit”
manual. Mount the Telescope along the top of any of the railings that do not interfere with any
areas that are activity openings.

2) The Roof Peak Support Triangle will need to be removed from the inside of the Roof Supports
located on the front of the play set. The Plastic Sunburst should be left off the front of the play
set. The “Treehouse Add On Kit” will be added to the front of the play set.

3) Flag Kits which normally reside on the front of the front corner posts at the top should be
relocated to the front slats on the “Treehouse Add On Kit”

Wood/Accessory and Hardware Lists:

These lists for the “Treehouse Add On Kit” are in the Appendix at the end of your play set
instruction manual or they are included with this sheet.

Steps to complete the “Treehouse Add On Kit”:

The instruction steps for the “Treehouse Add On Kit” are in the Appendix at the end of your play
set instruction manual or they are included with this sheet.

If you are adding the “Treehouse Add On Kit” to a playset that is already built:

It will be necessary to remove the Flags and Plastic Sunburst from the front side of your playset
wood roof. Then remove the 5/4 x 10” Roof Peak Support triangle from the inside of the front Roof
Supports. Keep these pieces and hardware since most will be reused during the construction
process.

Fill in the holes in the corner posts from the Flags with clear silicone (not included). If you wish to
fill the holes with a fastener then use #8 x 1” countersunk head screws with silicone in each hole.
You will need to purchase these screws at your local home center if you choose this option.

Fill any small holes in the Roof Supports leftover from removing the Plastic Sunburst with wood
filler. Use a stainable wood filler suitable for outdoor use. Then stain the wood filled spots with a
suitable matching color of stain.

2

«
...
165
166
167
168
169
...
»

Содержание 1501






























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1501

Бренд: Tar River Страницы: 26

Бренд: Rapid Shape Страницы: 12

Бренд: Maselec Страницы: 6

Бренд: Emos Страницы: 5

Бренд: Inxpect Страницы: 108

ULTRA-VEYOR SYSTEM

Бренд: Walinga Страницы: 56

AirCon Service Center

Бренд: Waeco Страницы: 68

Xpress Beam 7x12

Бренд: Evolite Страницы: 20

Бренд: Resolution Products Страницы: 2

Бренд: Sirona Страницы: 52

CONTOURA MJ76-360

Бренд: Major Страницы: 52

MASTERtorque LUX M9000 L COLOR 1.007.9900

Бренд: KaVo Страницы: 30

Бренд: Coherent Solutions Страницы: 27

Бренд: Carestream DENTAL Страницы: 43

Бренд: M-system Страницы: 3

Бренд: Beta Страницы: 12

Бренд: Robert Juliat Страницы: 48

Бренд: Chauvet Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды