PlayNation Play Systems 1501 Скачать руководство пользователя

Страница: 138 / 189

1" TO 1-3/4"

CHAIN MUST GO THROUGH

TWO BOARDS NO EXCEPTIONS!!

QUICK LINK

DETAIL A

SCALE 1 : 6

NOTE: TO ACHIEVE THE CORRECT

GAP YOU MAY NOT BE CONNECTING

THE END LINK OF EACH CHAIN. FOR

EXAMPLE YOU MAY HAVE TO

CONNECT THE SECOND, THIRD OR

FORTH LINKS TOGETHER.

2: THERE SHOULD BE AT LEAST A 1" TO 1-3/4" GAP BETWEEN THE BRIDGE DECK BOARD AND THE BOTTOM

THREAD THEM THROUGH THE QUICK LINK TO KEEP THEM UP AND OUT OF THE WAY.

IN A MANNER TO ACHIEVE THE CORRECT GAP. GO UNDERNEATH THE TOWER DECK AND USE A QUICK

PANEL BOARD ON THE TOWER. THIS MEANS THAT YOU WILL HAVE TO CONNECT THE ENDS OF THE CHAINS

STEP 21: BRIDGE DECK/CHAIN INSTALLATION

LINK TO ATTACH THE CHAINS TOGETHER. IF YOU HAVE LOOSE ENDS OF THE CHAINS HANGING DOWN

1: LAY THE BRIDGE DECK/CHAINS ASSEMBLY BETWEEN THE PLAY SET AND THE TOWER WITH THE CHAINS

FACING THE GROUND. THREAD THE CHAIN ENDS IN THE BRIDGE DECK ASSEMBLY THROUGH THE HOLES IN

THE BOTTOM PANEL BOARD AND DECK SUPPORT BOARD ON THE TOWER.

3: REPEAT THIS PROCESS AT THE PLAY SET

TO ATTACH THE CHAINS. AT THE PLAY SET EACH

CHAIN MUST GO THROUGH TWO BOARDS.

NO EXCEPTIONS.

128

Содержание 1501






























































































































































































Результаты поиска

Содержание 1501

Отзывы:

Похожие инструкции для 1501

Бренды по названию

Популярные бренды

PlayNation Play Systems 1501, Руководство по сборке

Результаты поиска

Содержание 1501

Отзывы:

Похожие инструкции для 1501

Бренды по названию

Популярные бренды