PlayNation Play Systems 1501 Скачать руководство пользователя

Страница: 69 / 189

RAMP SIDE

BOARD FIRST

LARGE HOLES SHOULD BE CLOSEST TO THE FLOOR

2 X 4 X 18-3/4"

RAMP SUPPORT

2-1/2"

WOOD SCREW

2 X 4 X 96"

INSTALL THIS BOARD SECOND

INSTALL THIS

44 34 "

CHECK TO SEE IF THESE TWO HOLES

ARE DRILLED THROUGH COMPLETELY

IN THE RAMP SIDES. IF THEY ARE NOT

DRILLED ALL THE WAY THROUGH THEN

CAREFULLY REAM THEM OUT WITH A

3/8" DRILL BIT.

ROUND END

STEP 16: CLIMBING RAMP

1: LAY OUT THE 2 X 4 X 96" RAMP SIDE BOARDS MAKING SURE THE LARGE HOLES ON TEH ENDS ARE CLOSEST TO THE

FLOOR.
2: FIRST PLACE ONE 2 X 4 X 18-3/4" RAMP SUPPORT BOARD AT THE SQUARE END OF THE 2 X 4 X 96" RAMP SIDE

BOARDS. OFFSET THE BOARD 1" FROM THE END. FASTEN THE RAMP SUPPORT BOARD TO THE RAMP SIDE BOARDS

WITH TWO 2-1/2" WOOD SCREWS PER SIDE.
3: SECOND PLACE ONE 2 X 4 X 18-3/4" RAMP SUPPORT BOARD AT THE ROUND END OF THE 2 X 4 X 96" RAMP SIDE

BOARDS. OFFSET THE BOARD 4" FROM THE ROUND END. FASTEN THE RAMP SUPPORT BOARD TO THE RAMP SIDE

BOARDS WITH TWO 2-1/2" WOOD SCREWS PER SIDE.
4: PLACE THE REMAINING 2 X 4 X 18-3/4" RAMP SUPPORT BOARD ACROSS THE RAMP SIDE BOARDS IN THE MIDDLE,

44-3/4" FROMT HE SQUARE END AND FASTEN WITH TWO 2-1/2" WOOD SCREWS PER SIDE.
NOTE: CLIMBING RAMP TO BE INSTALLED INSTEAD OF LADDER ON THIS MODEL. THE LADDER PARTS ARE INCLUDED

IN THE PACKAGE BUT ARE

NOT

USED.

Содержание 1501






























































































































































































Результаты поиска

Содержание 1501

Отзывы:

Похожие инструкции для 1501

Бренды по названию

Популярные бренды

PlayNation Play Systems 1501, Руководство по сборке

Результаты поиска

Содержание 1501

Отзывы:

Похожие инструкции для 1501

Бренды по названию

Популярные бренды