PlayNation Play Systems 1501 Скачать руководство пользователя

Страница: 189 / 189

of the Telescope Stand. Attach the half-circle shaped Telescope Bracket to the top of the

4 x 4 board with the1-1/4” phillips countersunk head screws provided.

the 4 x 4 board with the 1-1/4” phillips countersunk head screws provided.

3: Place the notched area of the second half-circle shaped Telescope Bracket over the

Mounting to 4 x 4 board

Telescope (07-0001)

top of the Telescope Stand. Attach the half-circle shaped Telescope Bracket to the top of

1: Center the Telescope Stand on top of the 4 x 4 board.

2: Place the notched area of one of the half-circle shaped Telescope Brackets over the top

!WARNING! **DO NOT LOOK INTO SUN OR OTHER BRIGHT LIGHTS WITH TELESCOPE**

Please note: Telescope does not magnify objects. Telescope is intended for make-believe-play by children.

*FOR RESIDENTIAL USE ONLY*

*FOR CHILDREN AGES 3-11*

4 x 4 board.

Telescope Stand

Half-Circle shaped

Telescope Bracket

1-1/4” Phillips

Countersunk Head Screws

Telescope

15-1/4" L x 4-1/4" W x 4” H

3 "

3 8

3 38 "

(See Mounting to 2 x 4 Board on the other side of this sheet if you wish to

mount the Telescope on the top of a 2 x 4 Board.)

Содержание 1501






























































































































































































Результаты поиска

Содержание 1501

Отзывы:

Похожие инструкции для 1501

Бренды по названию

Популярные бренды

PlayNation Play Systems 1501, Руководство по сборке

Результаты поиска

Содержание 1501

Отзывы:

Похожие инструкции для 1501

Бренды по названию

Популярные бренды