PlayNation Play Systems 1501 Скачать руководство пользователя

Страница: 137 / 189

1: PLACE A 5/16" WASHER BETWEEN THE 18TH CHAIN LINK AND THE BRIDGE DECK BOARD.

2: PLACE A 5/16" X 1-3/4" HEX BOLT WITH 5/16" WASHER THROUGH THE 18TH CHAIN LINK, THEN THROUGH

THE 5/16" WASHER, THEN THROUGH THE HOLE IN THE BRIDGE DECK BOARD AND SCREW IT INTO THE T-NUT.

TIGHTEN THE BOLT BUT NOT SO TIGHT THAT YOU CRACK THE WOOD.

3: COUNT OVER 4 CHAIN LINKS FROM THE LAST HEX BOLT. AT THIS CHAIN LINK PLACE A 5/16" WASHER

BETWEEN THE CHAIN LINK AND THE BRIDGE DECK BOARD. NOTE THAT THREE EMPTY CHAIN LINKS ARE

BETWEEN THE BOLTS.

4: PLACE A 5/16" X 1-3/4" HEX BOLT WITH 5/16" WASHER THROUGH THE CHAIN LINK, THEN THROUGH THE

5/16" WASHER, THEN THROUGH THE HOLE IN THE BRIDGE DECK BOARD AND SCREW IT INTO THE T-NUT.

TIGHTEN THE BOLT BUT NOT SO TIGHT THAT YOU CRACK THE WOOD.

5: REPEAT SUBSTEPS 3 & 4 UNTIL YOU HAVE SECURED THE CHAIN TO THE BRIDGE DECK BOARDS ALONG ONE

SIDE. THEN START OVER WITH THE OTHER CHAIN AND REPEAT THIS ENTIRE PROCESS.

STEP 20: BRIDGE DECK AND CHAIN ASSEMBLY

5/16" WASHER

COUNT OVER 4 LINKS FROM BOLT AND

DETAIL A

SCALE 1 : 4.5

THE NEXT BOLT GOES IN THIS LINK.

HEX BOLT

BRIDGE DECK BOARD)

(BETWEEN CHAIN AND

5/16" X 1-3/4"

5/16" WASHER

18TH CHAIN LINK

THREE EMPTY LINKS ARE

BETWEEN BOLTS.

127

Содержание 1501






























































































































































































Результаты поиска

Содержание 1501

Отзывы:

Похожие инструкции для 1501

Бренды по названию

Популярные бренды

PlayNation Play Systems 1501, Руководство по сборке

Результаты поиска

Содержание 1501

Отзывы:

Похожие инструкции для 1501

Бренды по названию

Популярные бренды