PlayNation Play Systems 1501 Скачать руководство пользователя

Страница: 165 / 189

ALIGN EDGE OF BORDER UNDER THE DECK

5) It will be very helpful to have an assistant at this stage. We recommend predrilling holes for the screws on the

Have your assistant push down on the board while you install a pan head screw and washer into the hole. Go

bridge deck boards. Mark through the center grommet onto the deck board. Drill a 1/8" hole by 1" deep.

bottom of the deckboards fastened to the chains. Align the edge of the mesh border with the end of the

go from the center grommet to the other side and do the same.

from the center grommet to one end of the mesh and repeat the mark/drill/install fasteners procedure. Then

BOARDS THAT ARE FASTENED TO THE CHAINS.

WITH THE END OF THE 2 X 4 BRIDGE DECK

MARK THROUGH THE CENTER OF THE CENTER

GROMMET ONTO THE MIDDLE DECK BOARD.

DRILL A 1/8" X 1" DEEP HOLE AT THE MARK.

PLACE A PAN HEAD SCREW THROUGH A

WASHER AND INSTALL INTO THE HOLE.

TRY TO CENTER THE WASHER ONTO THE

GROMMET BEFORE TIGHTENING COMPLETELY.

Example picture of the completed

Clatter Bridge Mesh Panels.

Содержание 1501






























































































































































































Результаты поиска

Содержание 1501

Отзывы:

Похожие инструкции для 1501

Бренды по названию

Популярные бренды

PlayNation Play Systems 1501, Руководство по сборке

Результаты поиска

Содержание 1501

Отзывы:

Похожие инструкции для 1501

Бренды по названию

Популярные бренды