PlayNation Play Systems 1501 Скачать руководство пользователя | Manualshive

Страница: 5 / 189

background image

PLAYNATION WARRANTY

2017

PlayNation will, at its discretion, replace any above ground part within the stated warranty period that is
defective in workmanship or materials. This decision is subject to verification of the defect, which, at
PlayNation's discretion, may be accomplished by submitting photographs or by delivery of the defective
part to PlayNation.

PlayNation Play Systems, Inc. • 190 Etowah Industrial Ct. • Canton, GA 30114 •

770-704-9300 Monday to Friday 9AM-5PM EST. Any warranty claim must include proof of purchase,
including the date of purchase.

In addition, within the first 30 days from the date of purchase,

PlayNation will replace any parts discovered to be missing from or damaged in the original packaging.

This warranty is valid only if the product is used for the purpose for which it was designed and installed
at a residential, single-family dwelling. This warranty is void if the product is used in a commercial,
institutional or multi-family setting.

This warranty does not cover normal wear and tear or (a) products

that have been damaged by acts of God and/or nature, negligence, misuse or accident; (b) products
that have been modified or repaired by unauthorized persons; (c) the cost of labor; or (d) the cost of
shipping any replacement product or part.

PLAYNATION DISCLAIMS ALL OTHER REPRESENTATIONS AND WARRANTIES OF ANY KIND, EXPRESSED,
IMPLIED, STATUTORY OR OTHERWISE, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. PLAYNATION WILL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES. This warranty is non-transferable and does not extend to the owners of the
product subsequent to the original purchaser. Some states do not allow limitations on implied
warranties or exclusion of incidental or consequential damages, so these restrictions may not be
applicable to you. This warranty gives you specific legal rights. You may also have other rights which vary
from state to state.

«
...
3
4
5
6
7
...
»

Содержание 1501






























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1501

Бренд: MacDon Страницы: 84

Бренд: MacDon Страницы: 89

Бренд: Dabi Atlante Страницы: 102

Бренд: MacDon Страницы: 2

Бренд: Falltech Страницы: 48

Бренд: Malekko Страницы: 2

Бренд: Major Страницы: 26

Бренд: Auto Meter Страницы: 30

Бренд: Velleman Страницы: 6

Бренд: pewag Страницы: 6

Бренд: MIXVIBES Страницы: 21

Fill-Air Rocket

Бренд: Sealed Air Страницы: 68

Бренд: Federal Signal Corporation Страницы: 44

Бренд: Hioki Страницы: 40

Бренд: Qtx Страницы: 4

Бренд: TSI Instruments Страницы: 42

Бренд: Caretec Страницы: 8

Бренд: Clearaudio Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды