PlayNation Play Systems 1501 Скачать руководство пользователя | Manualshive

Страница: 94 / 189

background image

SLIDE WILL BE ON THIS

SIDE.)

RIGHT SIDE OF PLAY SET

(ROCK WALL AND/OR

RIGHT ROOF SIDE

CHIMNEY (1)

FRONT OF PLAY SET

DORMERS (2)

STEP 33: ROOF

NOTE: THE SMALL PICTURE BELOW IS A GENERIC VIEW OF A PLAY SET IN OUR 1500 MODEL LINE. TYPICALLY THE ROCK WALL

AND/OR SLIDE IS LOCATED ON THE FRONT OF THE 1500 SERIES PLAY SETS. THE BIG PICTURE BELOW SHOWS THE RIGHT SIDE ROOF

WITH THE DORMER AND CHIMNEY. THE LEFT SIDE ROOF ONLY GETS A DORMER. INSTRUCTIONS TO BUILD THE CHIMNEY AND

DORMERS ARE IN THE APPENDIX AT THE BACK OF THIS MANUAL.
PLEASE NOTE THAT EACH SIDE OF THE ROOF WILL HAVE 11 ROOF BOARDS AND 1 ROOF FINISHER.
1: PLACE THE 1 X 5 X 47-1/2" ROOF BOARDS ON TOP OF THE ROOF SUPPORTS, FITTING THE TONGUE END INTO THE GROOVE

END OF THE ROOF STARTERS. EACH SIDE OF THE ROOF GETS 11 ROOF BOARDS.
2: FASTEN THE ROOF BOARDS TO THE ROOF SUPPORTS WITH 1-1/2" WOOD SCREWS
3: FIT THE TONGUE END OF THE 1 X 4 X 47-1/2" ROOF FINISHER INTO THE GROOVE END OF THE LAST ROOF BOARD. FASTEN IT TO

THE ROOF SUPPORT WITH FOUR 1-1/2" WOOD SCREWS.
TIP: INSTALL FOUR ROOF BOARDS AND THEN INSTALL THE CHIMNEY ACCORDING TO THE CHIMNEY INSTRUCTIONS. AFTER

INSTALLING THE EIGHTH ROOF BOARD INSTALL THE DORMER ACCORDING TO THE DORMER INSTRUCTIONS. THEN FINISH

INSTALLING THE REMAINING ROOF BOARDS AND ROOF FINISHER.

EACH SIDE OF THE

ROOF BOARD

ROOF BOARD

DORMER (ONE ON
ROOF)

(FIRST ONE)

ROOF BOARD

RIGHT ROOF SIDE

1 X 5 X 47-1/2"

1 X 5 X 47-1/2"

(FOURTH ONE)

(EIGHTH ONE)

CHIMNEY

1 X 5 X 47-1/2"

1 X 4 X 47-1/2"

ROOF FINISHER

84

«
...
92
93
94
95
96
...
»

Содержание 1501






























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1501

Бренд: Baker Instrument Company Страницы: 24

FX-ARM CONTROLLER

Бренд: Magicfx Страницы: 16

Бренд: Zetec Страницы: 23

Бренд: XDP Recreation Страницы: 40

Tablet1000 Series

Бренд: Hantek Страницы: 98

Бренд: Studiomaster Страницы: 10

Бренд: Delta Light Страницы: 2

Бренд: 3M ESPE Страницы: 150

Бренд: Moog Страницы: 13

Бренд: Weka Страницы: 36

Бренд: Primo Water Страницы: 16

Speed Tender 535-ST

Бренд: J&M Страницы: 67

Бренд: Little Cottage Страницы: 15

VARIOstar Series

Бренд: Zubler Страницы: 2

Бренд: VeEX Страницы: 2

Бренд: U-Line Страницы: 3

Бренд: Backyard Discovery Страницы: 92

Бренд: Luxium Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды