PlayNation Play Systems 1501 Скачать руководство пользователя

Страница: 188 / 189

Mounting to 2 x 4 board

Telescope (07-0001)

1: Place one of the "L" shaped Telescope Brackets against the 2 x 4 so that the bracket

section with the cutout faces up. Fasten the Telescope Bracket to the 2 x 4 with the 1-1/4"

phillips countersunk head screws provided.

2: Place the Telescope Stand inside the cutout section of the Telescope Bracket on top of

the 2 x 4.

3: Place another "L" shaped Telescope Bracket directly across from the other Telescope

Bracket. Fasten the Telescope Bracket to the 2 x 4 with the 1-1/4" phillips countersunk head

screws provided.

(See Mounting to 4 x 4 Board on the other side of this sheet if you wish to mount

the Telescope on the top of a 4 x 4 Board.)

!WARNING! **DO NOT LOOK INTO SUN OR OTHER BRIGHT LIGHTS WITH TELESCOPE**

Please note: Telescope does not magnify objects. Telescope is intended for make-believe-play by children.

*FOR RESIDENTIAL USE ONLY*

*FOR CHILDREN AGES 3-11*

"L’ Shaped Telescope Bracket

Telescope

Telescope Stand

15-1/4" L x 4-1/4" W x 4” H

1-1/4” Phillips

Countersunk Head

Screws

2 x 4 board

1 38 " to 1-1/2”

Содержание 1501






























































































































































































Результаты поиска

Содержание 1501

Отзывы:

Похожие инструкции для 1501

Бренды по названию

Популярные бренды

PlayNation Play Systems 1501, Руководство по сборке

Результаты поиска

Содержание 1501

Отзывы:

Похожие инструкции для 1501

Бренды по названию

Популярные бренды