PlayNation Play Systems 1501 Скачать руководство пользователя

Страница: 23 / 189

SWING BEAM LOADING

MAXIMUM SWING BEAM LOAD IS 425 LBS.

Weight Limits for Accessories:
The weight limit for a Swing Belt is 225 lbs. (Although 150lbs is the maximum recommended

swinging weight capacity for the swing position.)
The weight limit for a Trapeze Bar is 125 lbs.

Maximum Allowable swinging weight for a three position swing:
1) The maximum allowable swinging weight at each Swing Belt position is 150 lbs.

2) The maximum allowable swinging weight at the Trapeze position is 125 lbs.

3) The MAXIMUM SWING BEAM LOAD IS 425 lbs.

SWINGING WEIGHT

TRAPEZE BAR

REV A: 8/29/2012

125 LBS MAX

150 LBS MAX

SWINGING WEIGHT

150 LBS MAX

SWINGING WEIGHT

SWING BELT

THIS END

OF SWING

BEAM IS

ATTACHED

TO PLAY SET.

Содержание 1501






























































































































































































Результаты поиска

Содержание 1501

Отзывы:

Похожие инструкции для 1501

Бренды по названию

Популярные бренды

PlayNation Play Systems 1501, Руководство по сборке

Результаты поиска

Содержание 1501

Отзывы:

Похожие инструкции для 1501

Бренды по названию

Популярные бренды