PlayNation Play Systems 1501 Скачать руководство пользователя

Страница: 118 / 189

STEP 1: ATTACHING T-NUTS TO THE CORNER POSTS

LETTERS A, B, C AND D

ARE FOR REFERENCE

ONLY. YOUR POSTS

ARE NOT LABELED WITH

THESE LETTERS.

1: THIS STEP IS CRITICAL TO BUILDING THE FORT PROPERLY. IF ANY MISTAKES ARE MADE HERE, YOU WILL NEED TO

DIS-ASSEMBLE AND THEN RE-ASSEMBLE TO MAKE YOUR CORRECTIONS.

2: MAKE SURE HOLES ARE FREE OF ANY OBSTRUCTIONS. USE A BOLT TO CLEAN OUT ANY DEBRIS.

3: LAY OUT EACH OF THE 4 X 4 X 96" CORNER POSTS IN THE AREA YOU INTEND ON BUILDING THE TOWER OF THE

CLATTER BRIDGE.

4: USE THE DIAGRAM BELOW TO CORRECTLY IDENTIFY AND ORIENT THE NECESSARY DIRECTION THE POSTS SHOULD

FACE. NOTE LETTERS A, B, C AND D ARE FOR REFERENCE ONLY. YOUR POSTS ARE NOT LABELED WITH THESE

LETTERS.

5: USE A HAMMER TO SEAT THE T-NUTS AFTER INSERTING THEM INTO THE HOLES SHOWN IN THE DIAGRAM BELOW.

6: THE BARREL OF THE T-NUT SHOULD GO IN THE HOLE FIRST. HAMMER THE T-NUT UNTIL IT IS FLUSH/ALMOST FLUSH

TO THE CORNER POSTS.

4 x 4 x 96"

CORNER POST

T-NUT

FRONT OF

TOWER

108

Содержание 1501






























































































































































































Результаты поиска

Содержание 1501

Отзывы:

Похожие инструкции для 1501

Бренды по названию

Популярные бренды

PlayNation Play Systems 1501, Руководство по сборке

Результаты поиска

Содержание 1501

Отзывы:

Похожие инструкции для 1501

Бренды по названию

Популярные бренды