PlayNation Play Systems 1501 Скачать руководство пользователя | Manualshive

Страница: 53 / 189

background image

SANDBOX BOARD

(OFFSET HOLES DOWN)

(OFFSET HOLES DOWN)

2 X 6 X 47-1/2"

BOTTOM PANEL BOARD

DETAIL A

SWING BEAM SUPPORT

5/16" WASHER

4 X 4 X 47-1/2"

2 X 6 X 47-1/2"

5/16 X 4-1/2"

HEX BOLT

A

STEP 3: ASSEMBLING THE LEFT SIDE FRAME

1: LAY THE LEFT SIDE CORNER POSTS ON THE GROUND IN THEIR PROPER ORIENTATION.
2: LAY THE 2 X 6 X 47-1/2" SANDBOX BOARD ON TOP OF THE LEFT SIDE CORNER POSTS AT THE BOTTOM OF THE

CORNER POSTS. THE HOLES IN THE SANDBOX BOARD MUST BE OFFSET DOWN.
3: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE SANDBOX BOARD TO THE

T-NUTS INSTALLED ON THE CORNER POSTS. THE BOTTOM HOLES WILL BE USED LATER.
4: LAY THE 2 X 6 X 47-1/2" BOTTOM PANEL BOARD ON TOP OF THE LEFT SIDE CORNER POSTS IN THE MIDDLE OF THE

CORNER POSTS. THE HOLES IN THE BOTTOM PANEL BOARD MUST BE OFFSET DOWN.
5: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE BOTTOM HOLES OF THE BOTTOM PANEL

BOARD TO THE T-NUTS INSTALLED ON THE CORNER POSTS. THE TOP HOLES WILL BE USED LATER.
6: LAY THE 4 X 4 X 47-1/2" SWING BEAM SUPPORT ON TOP OF THE LEFT SIDE CORNER POSTS. THE THREE COUNTER-

SUNK HOLES IN THE MIDDLE OF THE SWING BEAM SUPPORT MUST FACE DOWNWARD.
7: FIND TWO TORQUE WASHERS. PLACE A 6-1/2" CARRIAGE BOLT THROUGH THE TORQUE WASHER, MAKING SURE

THAT THE TEETH ARE FACING IN THE SAME DIRECTION AS THE THREADS OF THE CARRIAGE BOLT. PLACE THE TORQUE

WASHER/CARRIAGE BOLT ASSEMBLY INTO THE CORNER POST HOLES SO THAT THE HEAD OF THE CARRIAGE

BOLT FACES WHAT WILL BE THE INSIDE OF THE FORT. USE A HAMMER TO SET THE TORQUE WASHER INTO THE CORNER

POST.
8: ATTACH THE SWING BEAM SUPPORT AS SHOWN

IN DETAIL A.

FRONT

OF

FORT

THE THREE COUNTER-

SUNK HOLES ON THE

SWING BEAM SUPPORT

WILL FACE DOWN WHEN

PROPERLY INSTALLED.

3/8" NUT

TORQUE WASHER

3/8" WASHER

BOLT CAP

6-1/2" CARRIAGE

BOLT

43

«
...
51
52
53
54
55
...
»

Содержание 1501






























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1501

Бренд: Raytech Страницы: 21

Бренд: Ocmis Irrigazione Страницы: 100

Бренд: Rane Страницы: 88

Бренд: Vanguard Instruments Страницы: 47

Бренд: XanLite Страницы: 2

Бренд: X-Rite Страницы: 6

Бренд: Quadro mdb Страницы: 11

Бренд: Parker Research Corp Страницы: 3

Бренд: ultraMEDIC Страницы: 28

NOVACAT X8 COLL

Бренд: Pottinger Страницы: 91

Бренд: Nuvo Страницы: 2

Бренд: unix Corporation Страницы: 6

Quest Enterprise Activity Unit QU10

Бренд: Play & Leisure Страницы: 6

Бренд: American DJ Страницы: 8

Бренд: Civemasa Страницы: 55

Бренд: SaMASZ Страницы: 28

stairville MH-Z1915

Бренд: thomann Страницы: 84

THE FLASH JUKE 12

Бренд: N-Gear Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды