Pioneer SC-09TX - Elite AV Network Receiver, Руководство по эксплуатации

Страница: 68 / 160

Other connections
08
68
En
1 Connect the front, surround, center and subwoofer
outputs on your DVD player to the corresponding
MULTI CH IN jack on this receiver.
• Use standard RCA/phono jack cables for the
connections.
2 If your DVD player also has outputs for surround
back channels, connect these to the corresponding
MULTI CH IN jacks on this receiver.
• Use standard RCA/phono jack cables for the
connections.
• If there is a single surround back output, connect it to
the
SURROUND BACK L (Single)
jack on this
receiver.
Selecting the multichannel analog inputs
If you have connected a decoder or a DVD player as
above, you must select the analog multichannel inputs
for surround sound playback.
1
With MULTI CH IN inputs, it is possible to switch the
number of channels of the input signal according to the
connected components. For example, when only two
channels of audio signals are being input to the MULTI
CH IN terminals, switch the number of playback
channels to
2 ch
using the
SIGNAL SEL
button.
1 Make sure you have set the playback source to the
proper output setting.
For example, you might need to set your DVD player to
output multichannel analog audio.
2 Use the INPUT SELECT button to select MULTI CH
IN.
You can also use the
INPUT SELECTOR
dial on the front
panel.
3 Set the operation selector switch to RCV.
4 Press the SIGNAL SEL button repeatedly to select
the number of channels of the input signal you want to
play.
The mode switches as shown below each time the button
is pressed.
• Depending on the DVD player you’re using, the
analog output level of the subwoofer channel may be
too low. In this case, the output level of the subwoofer
can be increased by 10 dB in the Multi Ch In Setup in
Other Setup. For details, see
Multi Channel Input
Setup on page 103.
Switching the speaker system
When the A/B speaker system is switched, the speakers
being played switches. Select the speaker system to be
used as necessary.
• Use the SPEAKERS terminals button on the front
panel to select a speaker system setting.
The modes that can be selected differ according to the
speaker output setting (see page 47).
The mode switches as shown below each time the button
is pressed.
When set to Normal
When set to All CH Bi-Amp
When set to Front Bi-Amp
When set to 7.2ch + ZONE 2
When set to 7.2ch + Speaker B
Note
1 • When playback from the multichannel inputs is selected, only the volume and channel levels can be set.
• You can’t listen to your speaker B system during playback from the multichannel inputs.
• With
MULTI CH IN
inputs, it is possible to play pictures simultaneously. For details, see
Multi Channel Input Setup
on page 103.
SOURCE
TV RCV
INPUT SELECT
TUNER
VOL
VOL CH
iPod HDMI PHONO
XM SIRIUS
INPUT SELECT
SOURCE
TV RCV
THX MPX MEMORY
STEREO
SIGNAL SEL SLEEP AUDIO
PHOTO
DIMMER
SR+ SBch PHASE
A.ATT GENRE HDMI OUT
D.ACCESS MCACC CLASS
DISP
CH
AUTO/
DIRECT STANDARD ADV.SURR
2 ch 6 ch
8 ch 7 ch
OFF A ON
A+B
ON
B ON
ON OFF
ON OFF
ON OFF
OFF A ON
A+B
ON
B ON
PHONES
SPEAKERS AUTO SURROUND
/STREAM DIRECT
STATUS
LCD
VIEW DIMMER TUNER EDIT BAND
CTRL ZONE2 ZONE3
VIDEO/GAME 2 INPUT
DIGITAL IN S-VIDEO VIDEO L R AUDIO
MULTI-ZONE CONTROL
MCACC
SETUP MIC
USB
(TUNE)
(TUNE)
PARAMETER
SETUP
(ST) (ST)
AUDIO VIDEO
RETURN
ENTER
SPEAKERS
SC_09TX.book Page 68 Monday, November 26, 2007 10:32 PM