Pioneer SC-09TX - Elite AV Network Receiver, Руководство по эксплуатации

Страница: 124 / 160

Additional information
14
124
En
Video
The PHASE CONTROL feature
doesn’t seem to have an audible
effect.
• If applicable, check that the lowpass filter switch on your subwoofer is off, or the lowpass cutoff is set to
the highest frequency setting. If there is a
PHASE
setting on your subwoofer, set it to 0º (or depending on
the subwoofer, the setting where you think it has the best overall effect on the sound).
• Make sure the speaker distance setting is correct for all speakers (see
Speaker Distance on page 58).
Noise or hum can be heard even
when there is no sound being
input. • Check that personal computers or other digital components connected to the same power source are not
causing interference.
There seems to be a time lag
between the speakers and the
output of the subwoofer. • See Automatically setting up for surround sound (MCACC & Full Band Phase Control) on page 12 to set up
your system again using MCACC (this will automatically compensate for a delay in the subwoofer output).
Can’t use the SR+ features. • Make sure that HDMI Control is set to OFF (see Setting the HDMI Control mode on page 99).
The maximum volume available
(shown in the front LCD display)
is lower than the
+12dB
maximum.
• This is not a malfunction. If the levels in
Channel Level
on page 57 have been adjusted, the maximum
volume will change accordingly.
No sound is output from the CD-
R/TAPE/MD OUT, DVR/VCR 1
OUT or DVR/VCR 2 OUT jack. • Make sure that ZONE 3 / RECSEL Setting in the ZONE Audio Setup menu is set to RECSEL (see
ZONE
Audio Setup on page 104).
Can’t select ZONE 3. • Make sure that
ZONE 3 / RECSEL Setting
in the
ZONE Audio Setup
menu is set to
ZONE 3
(see
ZONE
Audio Setup
on page 104).
Symptom Remedy
Symptom Remedy
No image is output when an input
is selected. • Check the video connections of the source component (see page 24).
• For HDMI, or when digital video conversion is switched off (in
Setting the Video options
on page 108), you
must connect your TV to this receiver using the same type of video cable as you used to connect your video
component.
• Make sure the input assignment is correct for components connected using component video, HDMI or
S-Video cables (see
The Input Setup menu
on page 101).
• Check the video output settings of the source component.
• Check that the video input you selected on your TV is correct.
• Some components (such as video game units) have resolutions that may not be converted. If adjusting
this receiver’s Resolution setting (in
Setting the Video options
on page 108) and/or the resolution settings on
your component or display doesn’t work, try switching Digital Video Conversion (in Setting the Video options
on page 108) OFF .
Can’t record video. • Check that the source is not copy-protected.
• The video converter is not available when making recordings. Check that the same type of video cable is
used for connecting both the recorder and the video source (the one you want to record) to this receiver.
Noisy, intermittent, or distorted
picture. • Sometimes a video deck may output a noisy video signal (during scanning, for example), or the video
quality may just be poor (with some video game units, for example). The picture quality may also depend on
the settings, etc. of your display device. Switch off the video converter and reconnect the source and display
device using the same type of connection (component, S-Video or composite), then start playback again.
ZONE2 video convert function
does not work. • Conversion is not possible when the video input signal is a component signal. Either use the composite
or S-Video terminal, or connect to the TV using a component cable.
• Turn the video convert function off and connect the source component and monitor with the same type
of cord.
The external image is not
displayed on the LCD screen or
the picture is disturbed. • The external video will not be displayed properly in the following conditions. Press the LCD VIEW button
to switch to the OSD mode.
– With HDMI inputs.
– When the video converter is off.
– When the resolution is set to PURE.
– When no external image is being input.
– When a non-compatible signal is being input.
SC_09TX.book Page 124 Monday, November 26, 2007 10:32 PM