Pioneer SC-09TX - Elite AV Network Receiver, Руководство по эксплуатации

Страница: 13 / 160

Simple Home Theater Guide
02
13
En
Make sure you do this before moving on to
Playing a
source
on page 14.
Important
• Make sure the microphone and speakers are not
moved during the Auto MCACC Setup.
• Using the Auto MCACC Setup will overwrite any
existing settings for the MCACC preset you select.
• Before using the Auto MCACC Setup, the
headphones should be disconnected and the iPod,
HOME MEDIA GALLERY, XM or SIRIUS Radio
function should not be selected as an input source.
Caution
• The test tones used in the Auto MCACC Setup are
output at high volume.
1 Switch on the receiver and your TV.
2 Connect the microphone to the MCACC SETUP MIC
jack on the front panel.
Place the microphone so that it’s about ear level at your
normal listening position (use a tripod if possible). Make
sure there are no obstacles between the speakers and
the microphone.
• Push down on the lower portion of the front panel
door to access the MCACC SETUP MIC jack:
The Auto MCACC display appears once the microphone
is connected.
1
3 Make sure ‘Normal’ is selected,
2
select an MCACC
preset
3
, then select START.
4
4 Follow the instructions on-screen.
Make sure the microphone is connected, and if you’re
using a subwoofer, make sure it is switched on and set to
a comfortable volume level.
5 Wait for the test tones to finish, then confirm the
speaker configuration in the OSD.
A progress report is displayed on-screen while the
receiver outputs test tones to determine the speakers
present in your setup. Try to be as quiet as possible while
it’s doing this.
5
If no operations are performed for 10 seconds while the
speaker configuration check screen is being displayed,
the Auto MCACC Setup will resume automatically. In this
case, you don’t need to select ‘
OK ’ and press ENTER in
step 6.
• With error messages (such as
Too much ambient
noise!
or
Check Microphone
) select
RETRY
after
checking for ambient noise (see Problems when
using the Auto MCACC Setup
below) and verifying the
mic connection. If there doesn’t seem to be a
problem, you can simply select
GO NEXT and
continue.
The configuration shown on-screen should reflect the
actual speakers you have.
6
DVD
RECEIVER SOURCE
MAIN
MULTI
OPERATION
ZONE2 3
DVR1
GALLERY
HOME MEDIA
INPUT SELECT
CD
TUNER iPod HDMI PHONO
CD-R
DVR2 VIDEO1 VIDEO2
BD TV SAT
SACD
XM SIRIUS
RECEIVER
AUDIO
PARAMETER
TOP MENU
BAND
CATEGORY
MENU
T.EDIT
VIDEO
PARAMETER
SETUP
SOURCE
TV RCV
INPUT MUTE
TUNE
TUNE
ST ST
MUTE
VOL
VOL
TV CONTROL
CH
Enter
SOURCE
TV RCV
SETUP
RETURN
SETUP
ENTER
PHONES
SPEAKERS AUTO SURROUND
/STREAM DIRECT
STATUS
LCD
VIEW DIMMER TUNER EDIT BAND CTRL ZONE2 ZONE3
VIDEO/GAME 2 INPUT
DIGITAL IN S-VIDEO VIDEO L R AUDIO
MULTI-ZONE CONTROL
MCACC
SETUP MIC
USB
(TUNE)
(TUNE)
PARAMETER
SETUP
(ST) (ST)
AUDIO VIDEO
RETURN
ENTER
Note
1 • You can’t use the System Setup menu in either the main or sub zone when the iPod, HOME MEDIA GALLAERY, XM or SIRIUS Radio input source is
selected. When you set
ZONE 2
,
ZONE 3
or
ZONE 2&3
to
ON
(page 74), you can’t use the System Setup menu.
• If you cancel the Auto MCACC Setup, or leave an error message for over three minutes, the screen saver will appear.
2 • The setting you should select differs according to the selected speaker layout/usage method (for example if you are planning to make bi-amp
connections, to set up another speaker system, etc.). For details see
Selecting the speaker layout/usage pattern
on page 10 and
Speaker output setting
on
page 47.
• If you have THX-certified speakers, select CUSTOM and choose YES for the THX Speaker setting.
3 The six MCACC presets are used for storing surround sound settings for different listening positions. Simply choose an unused preset for now (you can
rename it later in
Data Management
on page 54).
4 Note that correction curves are saved only when set to SYMMETRY . Select CUSTOM to save other correction curves (such as ALL CH ADJUST and
FRONT ALIGN ). See Automatic MCACC (Expert) on page 44 for more on this.
5 Do not adjust the volume during the test tones. This may result in incorrect speaker settings.
6 If you’re using the front LCD display, the diagram in
Listening to Surround Sound
above indicates (in bold) how each speaker is displayed.
1 . Au t o M C AC C
DV D / L D - 5 5 . 0 dB
O u t p u t S e t u p
[
N o r m a l ]
S av e S Y M M E T RY t o
[
M 1 . M E M O RY 1 ]
S TA RT
E N T E R : S t a r t : C a n c e l
N ow A n a ly z i n g … ( 2 / 1 0 )
E nv i ro n m e n t C h e ck
A m b i e n t N o i s e
[ O K ]
M i c ro p h o n e [ ]
S p e a k e r Y E S / N O [ ]
: C a n c e l
DV D / L D 0 . 0 dB
1. Auto MCACC
C H E C K
F ro n t [ Y E S ]
C e n t e r [ Y E S ]
S u r r A [ Y E S ]
S u r r B [ Y E S ]
S B [ Y E S x 2 ]
S W [ Y E S x 2 ]
O K
: C a n c e l
DV D / L D 0 . 0 dB
1 . Au t o M C AC C
10:Next
SC_09TX.book Page 13 Monday, November 26, 2007 10:32 PM