Other connections
08
65
En
Tip
• You can select channels directly by pressing
D.ACCESS
, then the three-digit channel number.
• The currently selected channel is automatically
chosen (without pressing
ENTER
) after 10 seconds.
Saving channel presets
This receiver can memorize up to 30 channels, stored in
three banks, or classes (A, B and C) of 10 channels each.
1
Select the channel you want to memorize.
See
Selecting channels and browsing by genre
above.
2
Set the operation selector switch to SOURCE, then
press T.EDIT.
The display shows a blinking memory class.
3
Press CLASS to select one of the three classes, then
press
/
to select the channel preset you want.
You can also use the number buttons to select a preset.
4
Press ENTER.
After pressing
ENTER
, the preset class and number stop
blinking and the receiver stores the SIRIUS channel.
1
Tip
• You can also press
MEMORY
during reception
display to save the information of up to five songs.
See
Using the SIRIUS Menu
below to recall this
information.
1
Listening to channel presets
You will need to have some presets stored to do this.
1
Set the operation selector switch to SOURCE, then
press CLASS to select the class in which the channel is
stored.
Press repeatedly to cycle through classes A, B and C.
2
Press
/
to select the channel preset you want.
• You can also use the number buttons on the remote
control to recall the channel preset.
Using the SIRIUS Menu
The SIRIUS Menu provides additional SIRIUS Radio
features.
1
1
Set the operation selector switch to SOURCE, then
press TOP MENU.
2
Use
/
to select a menu item, then press ENTER.
Choose from the following menu items:
•
Channel Skip/Add
– Use
/
and
ENTER
to select
channels you would like to remove/restore from/to
the channel guide.
•
Parental Lock
– Use
/
and
ENTER
to select
channels you would like to place under parental lock.
Channels put under parental lock are not displayed in
the Channel Guide, but may be accessed by directly
inputting their channel number and providing the
parental lock password.
•
Antenna Aiming
– Check the strength of satellite
and terrestrial reception.
•
Memory Recall
– Use
/
to browse your saved
song information (see
Tip
above).
•
Password Set
– Set the parental lock password.
3
When you’re finished press TOP MENU to return to
the reception display.
Using the i.LINK interface
If you have a component with an i.LINK connector, you
can connect it to this receiver using an i.LINK cable.
Since the i.LINK interface does not transmit video
signals, the video signal of i.LINK-connected
components must be connected with other cables (see
Connecting your equipment
on page 17 for more on
making video connections). If you’ve already hooked up
the video signal from the component, assign the i.LINK
input to the input function to which you’ve connected the
video signals (see
The Input Setup menu
on page 101).
See
Checking the i.LINK inputs
on page 66 to confirm
your i.LINK settings.
The two i.LINK connectors on the rear of your receiver are
4-pin connectors. Use a 4-pin, S400 i.LINK cable to
connect i.LINK-equipped components.
Caution
• If your i.LINK connector comes into contact with
metallic parts of the receiver other than the i.LINK
terminal, an electrical short may occur. Some cables
have metal parts that may touch the unit when
connected. Please take care to use a suitable i.LINK
cable only.
Important
• Please use 4-pin, S400 cables less than 3.5 meters
long. Although longer ones are available, they may
not work reliably.
• There may be cases where the PQLS/rate control
function and/or the i.LINK audio does not work
properly even when connected to i.LINK Audio-
compatible equipment.
• Do not connect/disconnect i.LINK cables or switch
on/off any components connected using i.LINK when
the receiver is on.
Note
1 You can reset the Channel presets, Memory, Channel Skip/Add, Parental Lock and Password settings in
Resetting the system
on page 111.
SC_09TX.book Page 65 Monday, November 26, 2007 10:32 PM
Содержание SC-09TX - Elite AV Network Receiver
Страница 1: ...uctions REC ...
Страница 160: ......
