PHILIPS Respironics DreamStation BiPAP AVAPS страница 15 Скачать руководство пользователя | Manualshive

Страница: 15 / 144

background image

P

AGE

15

1127179,

V

ER

.

02

D

REAM

S

TATION

B

I

PAP

S/T

AND

AVAPS

S

ERVICE

&

T

ECHNICAL

R

EFERENCE

M

ANUAL

Chapter 4.

Cleaning and Disinfection

4.1 Cleaning and Disinfecting: Device and Humidifier Exterior

CAUTIONS

Only the cleaning and disinfection procedure listed in this manual are recommended by Respironics.
Use of other cleaning and disinfecting processes, not specified by Respironics, may affect the
performance of the product. If there are any uncertainties related to the disinfectants you are using,
please contact Philips Respironics to see if they are approved for use.

Follow all instructions from the manufacturer of the disinfectant product. Any deviation from these
instructions, the manufacturer’s instructions, or agents not listed in this guide may impact the
performance of the product. Review all applicable instructions for additional warnings and cautions.

WARNING

To avoid electrical shock, always unplug the power cord from the wall outlet before cleaning the
device. DO NOT immerse the device in any fluids.

Perform the following steps to clean and disinfect the device and humidifier prior to servicing the devices:

1. Turn the device off and disconnect from the power source before cleaning.
2. Remove and dispose of the blue pollen filter and light-blue disposable ultra-fine filter (if returned with

the device).

3. As needed, clean the device and humidifier exterior using a mild liquid dishwashing detergent. Use a

mixture of 1 teaspoon (5 milliliters) dishwashing detergent/1 gallon (3.8 liters) of water.

4. Allow the device and humidifier to air dry. Use one of the following to disinfect all exterior surfaces of

the device and humidifier, including the filter and accessory access doors.

•

DisCide Ultra Towelettes

•

Cloth with chlorine bleach (8% sodium hypochlorite), 1 to 10 part reduction with water.

5.  Pay close attention to all corners and crevices.
6.  Open the humidifier lid and disinfect the latch area.
7.  Allow the device and humidifier to air dry completely before plugging in the power cord and turning

the device on.

«
...
13
14
15
16
17
...
»

Содержание DreamStation BiPAP AVAPS

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для DreamStation BiPAP AVAPS

Бренд: Sabre Страницы: 53

Бренд: Lotus Страницы: 3

PORTABLE NEBULIZER WITH MESH TECHNOLOGY

Бренд: FarmaMed Страницы: 116

Бренд: 3M Страницы: 64

Бренд: OCENCO Страницы: 13

Бренд: Silverline Страницы: 2

Бренд: TREND Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды