PHILIPS Respironics DreamStation BiPAP AVAPS страница 89 Скачать руководство пользователя | Manualshive

Страница: 89 / 144

background image

P

AGE

89

1127179,

V

ER

.

02

D

REAM

S

TATION

B

I

PAP

S/T

AND

AVAPS

S

ERVICE

&

T

ECHNICAL

R

EFERENCE

M

ANUAL

Alert

Icon

Priority

Description

User Action

Patient Message

Notification

Message from your
Provider.

Press Control Dial to
acknowledge and clear the
message.

Change Rejected

Alert

A prescription or
settings change was
rejected.

N/A

Humidification Error.
Contact support if the
problem persists.

Status

Humidifier error (only
when humidifier is pre-
sent)

Humidifier heater
plate error or
humidifier not
properly connected
to therapy device.

Turn off device and discon-
nect from power. Detach the
humidifier, visually check that
electrical contacts are clear,
then reconnect humidifier and
power cord.

Heated Tube Error.
Contact support if the
problem persists

Status

Heated tube error
(only when heated
tube is present).

Heated tube may be
overheated or dam-
aged.

Turn off device.  Detach
heated tube from
humidifier,  make sure that
tube  is not covered or
obstructed, and then
reattach to humidifier.  If
alert continues,
troubleshoot for possible
failure.

The attached power
supply does not support
humidification.

Alert

Indicates that the
attached power
supply is not
capable of
supporting
humidification or
heated tube.

Switch to a Philips
Respironics  DreamStation
power supply that is
capable of supporting
humidification.  Or operate
therapy  device without
humidifier.

Activate MODE?

Notification

Indicates an incompati-
ble power supply is at-
tached. Incompatible
power supply, or
power cord is not fully
inserted into device’s
power inlet.

Confirm power cord is fully
inserted into device’s power
inlet. Confirm a compatible
Philips Respironics power
supply is attached. Switch to
compatible power supply if
needed.

«
...
87
88
89
90
91
...
»

Содержание DreamStation BiPAP AVAPS

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для DreamStation BiPAP AVAPS

Бренд: Scott Страницы: 36

Бренд: Seac Страницы: 16

Бренд: Perel Страницы: 2

Бренд: Roscoe Medical Страницы: 32

Бренд: Plusmed Страницы: 24

Бренд: Plusmed Страницы: 76

Бренд: Drive Medical Страницы: 8

Бренд: Drive Medical Страницы: 40

Бренд: Citizen Страницы: 2

Бренд: Citizen Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды