PHILIPS Respironics DreamStation BiPAP AVAPS Скачать руководство пользователя страница 97

Страница: 97 / 144

AGE

1127179,

REAM

TATION

PAP

S/T

AND

AVAPS

ERVICE

ECHNICAL

EFERENCE

ANUAL

Replacing the UI Panel

Kit

Included in Kit

Tools Required

UI Panel Assembly

•

UI Panel

•

Torx Screwdriver (T10 is
recommended)

To remove the UI Panel:

1. Remove all components as instructed in the previous sections.

2. Lift the UI Panel away from the device.

Note:

the alarm ribbon cable may detach when you pull the UI Panel away from the device. If it does

not detach, remove it by hand by gently lifting up on the ribbon.

3. Detach the main UI Panel ribbon from the PCA by lifting up on the connector latch and pulling the rib-

bon away from the connector.

To install the UI Panel:

1. Align the UI Panel ribbon into the connector latch on the PCA.

2. Snap down the connector latch to hold the ribbon in place.

3. Verify the UI connection is properly seated.

4. Attach the alarm ribbon cable to the PCA.

Note:

you may seat the UI Panel, and then attach the cable to the PCA if you find it easier.

5. Seat the UI Panel into Bottom Enclosure grooves (see illustrations below).

6. Assemble the remainder of the device as instructed in the previous sections.

Alarm Ribbon

Cable

Main Ribbon

Cable

(unclasp)

Содержание DreamStation BiPAP AVAPS
















































































































































Результаты поиска

Содержание DreamStation BiPAP AVAPS

Отзывы:

Бренды по названию

Популярные бренды

PHILIPS Respironics DreamStation BiPAP AVAPS, Сервисное и техническое руководство

Результаты поиска

Содержание DreamStation BiPAP AVAPS

Отзывы:

Бренды по названию

Популярные бренды