Peterbilt 325 2017 Скачать руководство пользователя страница 243

Страница: 243 / 392

PREVENTIVE MAINTENANCE SCHEDULE

PREVENTIVE MAINTENANCE (PM) INTERVALS

Recommended PM

Interval

SYSTEM

COMPONENT

MAINTENANCE TASK

Headlamps

Check the aim and adjust as required.

Warning lights in light bar

Check at the ignition start position to verify bulbs and driver
information display function (shown on page 3-11).

Turn, Stop, Reverse lights
and signals

Visual check.

Check operation and output.

Check tightness of the pulley nut.

Check the tension of the drive belt (shown on page 5-102).

Alternator

Check tightness of the terminal hex nuts.

Starter

Check torque on hex nuts.

ECM connector

Check the tightness of the ECM connector.

Electrical &
lights

Wheel sensors

Check for damaged sensors and connectors, and worn or frayed
wires.

(03/17)

Y53-6060-1C1

5-33

Содержание 325 2017









































































































































































































































































































































































































Результаты поиска

Содержание 325 2017

Отзывы:

Бренды по названию

Популярные бренды

Peterbilt 325 2017, Руководство оператора

Результаты поиска

Содержание 325 2017

Отзывы:

Бренды по названию

Популярные бренды