manualshive.com logo in svg

Peterbilt 325 2017, Руководство оператора

Поделиться
Скачать
Peterbilt 325 2017 Скачать руководство пользователя страница 167

OPERATING THE BRAKE SYSTEM

NOTE

For doubles or triples, the lamp does
not distinguish between trailers. An
ABS problem in any of the trailers
will activate the Trailer ABS Warning
Lamp.

NOTE

If you change the intended service in
any way (i.e. number of axles, mul-
tiple trailers, add switchable trailer
accessories, etc.)

from the date

the vehicle was manufactured, you
should contact your trailer manufac-
turer and/or trailer anti-lock brake
manufacturer to determine if the
power available at the 7-way trailer
light line is adequate. Failure to do
so might result in insufficient power
to the trailer ABS system which may
affect its operation.

CAUTION

The center pin of the 7-way trailer
light line may be constantly powered
for ABS. Make sure it will not acci-
dently turn on trailer equipment.

Special Trailer ABS (Without PLC)
Option

If a trailer does not have PLC,

but

it does have ABS that is powered
through an optional second trailer
connector (ISO 3731) and that trailer
ABS is designed to control the Trailer
ABS Warning Lamp in the cab

and

the vehicle has been ordered with the
option to turn on this lamp for these
types of trailers,

then

this lamp will turn

on when that trailer ABS has a system
problem. This should be checked by a
dealer as soon as possible. The Trailer
ABS Warning Lamp will not turn on for
the power-on test when connected to
these types of trailers.

NOTE

Very few trailers built before 3/1/01
have this option. Trailers built after
3/1/01 are built with PLC technology.

(03/17)

Y53-6060-1C1

4-27

4

Содержание 325 2017









































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды