Peterbilt 325 2017 Скачать руководство пользователя страница 237

Страница: 237 / 392

PREVENTIVE MAINTENANCE SCHEDULE

PREVENTIVE MAINTENANCE (PM) INTERVALS

Recommended PM

Interval

SYSTEM

COMPONENT

MAINTENANCE TASK

Pitman arm clamp bolt and
nut

Check the torque; tighten to specified torque value as required.

Steering intermediate shaft

Check the torque on the pinch bolt and nut.

Steering intermediate shaft
U-joints (ON HIGHWAY)

Lubricate [EP NLGI #2 HD grease, +325° F to -10° F (+163° C
to -23° C) range].

Steering intermediate shaft
U-joints (OFF HIGHWAY or
CITY DELIVERY)

Lubricate [EP NLGI #2 HD grease, +325° F to -10° F (+163° C
to -23° C) range].

Draglink and tie rod arm ball
sockets (ON HIGHWAY)

Lubricate (EP NLGI #2 lithium-based, moly-filled, HD grease).

Power
Steering

Draglink and tie rod arm ball
sockets (OFF HIGHWAY or
CITY DELIVERY)

Lubricate (EP NLGI #2 lithium-based, moly-filled, HD grease).

(03/17)

Y53-6060-1C1

5-27

Содержание 325 2017









































































































































































































































































































































































































Результаты поиска

Содержание 325 2017

Отзывы:

Бренды по названию

Популярные бренды

Peterbilt 325 2017, Руководство оператора

Результаты поиска

Содержание 325 2017

Отзывы:

Бренды по названию

Популярные бренды