manualshive.com logo in svg

Peterbilt 325 2017, Руководство оператора

Поделиться
Скачать
Peterbilt 325 2017 Скачать руководство пользователя страница 304

ELECTRICAL

NOTE

Make sure to reconnect the ground
(negative) cable last.

1.

Place batteries in vehicle and
tighten bolt of holding plate.

2.

Reconnect positive cable.

3.

Reconnect ground (negative)
ground cable.

WARNING!

Battery replacement may alter or
disturb battery cable routing. Check
to insure battery cables are free
from any point of chaffing. Failure
to comply may result in death, per-
sonal injury, equipment or property
damage.

Replacing Parts Removed for
Access

1.

Replace battery cover.

2.

Install 2 bolts in step strut. Torque
to 24-32 lb-ft (33-43 Nm).

3.

Install fairing and install 4 bolts.
Torque to 6-7 lb-ft (8-9 Nm).

4.

Install steps by installing 2 bolts in
each step. Torque to 24-32 lb-ft
(33-43 Nm).

WARNING!

Always reinstall the steps before en-
tering the cab. Without the steps you
could slip and fall, resulting in possi-
ble injury to yourself.

WARNING!

Fairings not installed properly could
come loose and cause other mo-
torists to have an injury accident. It
is important that fairings be installed
properly. Failure to comply may re-
sult in death, personal injury, equip-
ment or property damage.

WARNING!

Before attempting any work on the
batteries or electrical system, re-
move all jewelry. If metal jewelry or
other metal comes in contact with
electrical circuits, a short circuit may
occur causing you to be injured, as
well as electrical system failure and
damage.

5-94

Y53-6060-1C1

(03/17)

5

Содержание 325 2017









































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды