Peterbilt 325 2017 Скачать руководство пользователя | Manualshive

Страница: 23 / 392

background image

GETTING TO YOUR ENGINE

3. Pull Up to Separate

4. Hood Latch in the Open Position

Hood Tilt

WARNING!

A pivoting hood could hurt some-
one or be damaged itself. Before
opening or closing the hood, be sure
there are no people or objects in the
way. Failure to stand in a position of
safety can cause death or personal
injury.

WARNING!

Before opening the hood, make sure
your footing is secure and stable.
Failure to do so may cause the hood
to close uncontrollably which may
result in death or personal injury.

Put one hand on the hood handle (just
above the Peterbilt emblem), one foot
on the bumper, and one foot on the
ground. Tilt the hood forward.

(03/17)

Y53-6060-1C1

1-17

1

«
...
21
22
23
24
25
...
»

Содержание 325 2017









































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 325 2017

Бренд: RAM Страницы: 86

Бренд: Southworth Страницы: 34

Бренд: CMCO Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды