manualshive.com logo in svg

Peterbilt 325 2017, Руководство оператора

Поделиться
Скачать
Peterbilt 325 2017 Скачать руководство пользователя страница 220

PREVENTIVE MAINTENANCE SCHEDULE

WARNING!

Disconnect the battery ground strap
whenever you work on the fuel sys-
tem or the electrical system. When
you work around fuel, do not smoke
or work near heaters or other fire
hazards. Keep an approved fire ex-
tinguisher handy. Failure to comply
may result in death, personal injury,
equipment or property damage.

WARNING!

Always support the vehicle with ap-
propriate safety stands if it is neces-
sary to work underneath the vehicle.
A jack is not adequate for this pur-
pose. Failure to comply may result
in death, personal injury, equipment
or property damage.

WARNING!

When working underneath the vehi-
cle without appropriate safety stands
but with the wheels on the ground
(not supported), make sure that (1)
the vehicle is on hard level ground,
(2) the parking brake is applied, (3)
all wheels are blocked (front and
rear) and (4) remove the ignition
key so that the engine cannot be
started. Failure to comply may result
in death, personal injury, equipment
or property damage.

WARNING!

Never start or let the engine run in
an enclosed, unventilated area. Ex-
haust fumes from the engine contain
carbon monoxide, a colorless and
odorless gas. Carbon monoxide can
be fatal if inhaled. Failure to comply
may result in death, personal injury,
equipment or property damage.

The following pages contain a table
of maintenance tasks with the related
intervals for each task on the right
side of the table. The top of the table
displays a guide to a maintenance
interval and its schedule. Some
tasks are dependent on the vehicle
application. These tasks will be
shown as separate tasks and will have
the words "ON HIGHWAY", "CITY
DELIVERY" or "OFF-HIGHWAY"
after the description. These tasks
are differentiated because they are
dependent on the vehicle’s operating
environment.

On highway is defined for applications
where the vehicle is NOT used off of a
paved road during normal operation.

City Delivery is defined for applications
where frequent start and stopping is
required during normal operation and
the highway is used infrequently and
for short periods of time.

5-10

Y53-6060-1C1

(03/17)

5

Содержание 325 2017









































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды