manualshive.com logo in svg

Peterbilt 325 2017, Руководство оператора

Поделиться
Скачать
Peterbilt 325 2017 Скачать руководство пользователя страница 308

ELECTRICAL

Electrical and Alternator
Precautions

Take the following precautions to
avoid burning out alternator diodes:

•

Do not start the engine
with alternator disconnected
(connections removed) from the
circuit.

•

Before welding, disconnect all
electronic connections to the
vehicle batteries.

•

Remove battery power cable and
insulate it from the vehicle.

•

Do not run the engine with the
batteries disconnected.

•

Do not disconnect the battery
cables or alternator connection
cables with the engine running.

•

Never turn the ignition switch from
the ON position to the START
position with the engine running.

•

When charging the battery
(installed in the vehicle) disconnect
the battery cables.

•

Do not reverse the cables of the
alternator, starter motor, or battery.

•

Do not polarize the alternator. The
alternator should not be polarized
like a generator. To ensure correct
polarity, use a test lamp or a
voltmeter.

Remote Keyless Entry

The remote keyless entry system may
become inoperational due to a key
fob battery. If you have issues with
a key fob, replace the battery and
re-synchronize the key fob. In some
situations, the key fob may need to
be replaced and in others, a fuse may
have failed and may render both key
fobs inoperative.

Contact your dealer for more help if
a key fob does not work and it is not
because of a bad battery.

5-98

Y53-6060-1C1

(03/17)

5

Содержание 325 2017









































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды