Peterbilt 325 2017 Скачать руководство пользователя | Manualshive

Страница: 26 / 392

background image

SEATS AND RESTRAINTS

SEATS AND
RESTRAINTS

Introduction

This section covers the operation
and safe use of your seats. For
further information on features and
adjustment of the seat, see the
manufacturer's Service and Operation
Manual included with the vehicle.

Seat Adjustment

WARNING!

Do not adjust the driver's seat while
the vehicle is moving.

The seat

could move suddenly and unexpect-
edly and can cause the driver to
lose control of the vehicle. Make all
adjustments to the seat while the
vehicle is stopped. After adjusting
the seat and before driving off, al-
ways check to ensure that the seat
is firmly latched in position. Failure
to comply may result in death, per-
sonal injury or property damage.

WARNING!

Before driving or riding in vehi-
cle, ensure that there is adequate
head clearance at maximum upward
travel of seat. Injury may occur if
head clearance is not adequate.
Failure to comply may result in death
or personal injury.

Standard Driver's Seat

The standard driver's seat can be
adjusted forward and rearward. These
movements are each controlled by
levers located on the FRONT of the
seat.

Driver's Seat with Air Suspension
(Option)

WARNING!

Before driving or riding in the vehi-
cle, be sure that there is adequate
head clearance at maximum upward
travel of seat. Serious injury may
occur if head clearance is not ade-
quate.

The driver's seat with air suspension
can be adjusted using the controls
pictured.

1-20

Y53-6060-1C1

(03/17)

1

«
...
24
25
26
27
28
...
»

Содержание 325 2017









































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 325 2017

Бренд: DAF Страницы: 58

Бренд: Power Step Страницы: 27

2014 TRUCK 1500

Бренд: RAM Страницы: 40

Бренд: Neilsen Страницы: 33

Reefer 2023 Series

Бренд: Kässbohrer Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды