Peterbilt 325 2017 Скачать руководство пользователя | Manualshive

Страница: 283 / 392

background image

CAB

Vehicle Cleaning

Precautions

WARNING!

Handle cleaning agents carefully.
Cleaning agents may be poisonous.
Keep them out of the reach of chil-
dren. Failure to comply may result
in death, personal injury, equipment
or property damage.

WARNING!

Do not use gasoline, kerosene,
naphtha, nail polish remover or other
volatile cleaning fluids. They may
be toxic, flammable or hazardous
in other ways.

Failure to comply

may result in death, personal injury,
equipment or property damage.

WARNING!

Do not clean the underside of chas-
sis,

fenders wheel covers,

etc.

without protecting your hands and
arms.

You may cut yourself on

sharp-edged metal parts.

Failure

to comply may result in death, per-
sonal injury, equipment or property
damage.

WARNING!

Moisture, ice, and road salt on
brakes may affect braking efficiency.
Test the brakes carefully after each
vehicle wash.

Failure to comply

may result in death, personal injury,
equipment or property damage.

•

Observe all caution labels.

•

Always read directions on the
container before using any
product.

•

Do not use any solution that can
damage the body paint.

•

Most chemical cleaners are
concentrates which require
dilution.

•

Only use spot removing fluids in
well ventilated areas.

•

Any vehicle is subjected to
deterioration from industrial
fumes, ice, snow, corrosive road
salt, etc., to name just a few
causes. A well-cared-for vehicle
can look like new many years
later. Regular and correct care
will contribute to maintaining the
beauty and the value of your
vehicle.

Your dealer has a number of
vehicle-care products and can advise
you on which ones to use for cleaning
the exterior and interior of your vehicle.

(03/17)

Y53-6060-1C1

5-73

5

«
...
281
282
283
284
285
...
»

Содержание 325 2017









































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 325 2017

Бренд: Komatsu Страницы: 258

Бренд: AMOG Страницы: 112

Бренд: Krone Страницы: 92

Kenworth T800 2012

Бренд: Paccar Страницы: 276

1500 CLASSIC 2022

Бренд: RAM Страницы: 364

Бренд: Franklin Страницы: 8

Бренд: STAXX Страницы: 33

Бренд: GMC Страницы: 294

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды