Peterbilt 325 2017 Скачать руководство пользователя | Manualshive

Страница: 362 / 392

background image

TIRES AND WHEEL

with the disc brake assembly. When
installing any replacement wheel,
always inspect the tires/wheels to
ensure there is adequate clearance
between other vehicle components.

With the hood open, check for
clearance between the wheel and disc
brake assembly. Use a hydraulic jack
to raise the front of the vehicle off
the ground to allow the wheel to spin
freely. While rotating the wheel, check
to ensure there is adequate clearance
between the wheel and disc brake
assembly

WARNING!

If the hood falls, anyone under it
could be injured. Always make sure
that the hood hold open device en-
gages when the hood is in its open
position any time anyone gets under
the hood for any reason.

•

The hood could hurt someone
that is in the way of its descent.
Before lowering the hood, be
sure no objects or people are in
the way.

WARNING!

Always support the vehicle with ap-
propriate safety stands if it is neces-
sary to work underneath the vehicle.
A jack is not adequate for this pur-
pose.

WARNING!

Improperly mounting and demount-
ing tire and rim assemblies is dan-
gerous. Failure to observe proper
precautions could cause the tire-rim
assembly to burst explosively, caus-
ing death or personal injury.

See

the wheel manufacturer's literature
for the proper way to mount and de-
mount your tires and rims. Follow
their precautions exactly.

5-152

Y53-6060-1C1

(03/17)

5

«
...
360
361
362
363
364
...
»

Содержание 325 2017









































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 325 2017

Бренд: Komatsu Страницы: 420

Бренд: HELI Страницы: 20

Бренд: U-Line Страницы: 9

Бренд: MAFI Страницы: 152

Бренд: URAL Motorcycles Страницы: 321

Бренд: Flextool Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды