Peterbilt 325 2017 Скачать руководство пользователя страница 373 | Manualshive

Страница: 373 / 392

Peterbilt 325 2017 Скачать руководство пользователя страница 373

CONSUMER INFORMATION AND VEHICLE IDENTIFICATION

Components and Weights Label

The Components and Chassis Weight
Label is located on either the driver’s
side door edge or on the driver’s
side door frame. It includes chassis
number, chassis weight and gross
weight, plus model information for the
vehicle, engine, transmission, and
axles.

Tire and Rim Data Label

The Tire, Rim and Weight Rating
Data Label is located on the driver’s
side door edge or on the driver’s side
door frame. It contains the following
information:

•

GVWR - Gross Vehicle Weight
Rating

•

GAWR FRONT, INTERMEDIATE
and REAR - Gross Axle Weight
Ratings for Front, Intermediate
and Rear Axle

•

TIRE/RIM SIZES AND INFLATION
PRESSURES - Tire/Rim Sizes
and Cold Pressure Minimums

•

VIN including CHASSIS NUMBER

WARNING!

Do not exceed the specified load rat-
ing. Overloading can result in loss
of vehicle control and personal in-
jury, either by causing component
failures or by affecting vehicle han-
dling. Exceeding load ratings can
also shorten the service life of the
vehicle.

The components of your vehicle
are designed to provide satisfactory
service if the vehicle is not loaded
in excess of either the gross vehicle
weight rating (GVWR), or the maximum
front and rear gross axle weight ratings
(GAWRs).

NOTE

GVW is the TOTAL SCALE WEIGHT
the vehicle is designed to carry. This
includes the weight of the empty ve-
hicle, loading platform, occupants,
fuel, and any load.

(03/17)

Y53-6060-1C1

6-5

6

«
...
371
372
373
374
375
...
»

Содержание 325 2017









































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды