Peterbilt 325 2017 Скачать руководство пользователя

Страница: 77 / 392

WARNING SYMBOLS

Optional Lights:

Additional lights may be operational
depending on individual vehicle
specifications. These will be included
in the Instrument System Self Test.

NOTE

Some optional lights may illumi-
nate even though your vehicle is not
equipped with that particular fea-
ture.

Warning Light / Indicator
Symbols

The following is a list of Warning Light
/ Indicator Symbols. Reading left to
right, the table header identifies:

•

the Symbol Name

•

the appearance of the Symbol

•

the Symbol Color when it is
illuminated

•

whether the symbol is standard
(Std) or optional (Opt)

•

whether the symbol has an
associated check message

•

the Page Number reference for
additional information

Symbols are listed by major component
sections.

Example: Engine, and then in
alphabetical order.

Warning Light/Indicator Symbols

Symbol Name

Symbol

Color

Std/

Opt

Msg

Page

1. Active Warnings, Exclamation Point

Red

Std

on page 3-19

2. Active Warnings, Number

Yellow

Std

on page 3-19

(03/17)

Y53-6060-1C1

3-11

Содержание 325 2017









































































































































































































































































































































































































Результаты поиска

Содержание 325 2017

Отзывы:

Похожие инструкции для 325 2017

Бренды по названию

Популярные бренды

Peterbilt 325 2017, Руководство оператора

Результаты поиска

Содержание 325 2017

Отзывы:

Похожие инструкции для 325 2017

Бренды по названию

Популярные бренды