Paso PA8506-V Скачать руководство пользователя страница 65

Страница: 65 / 68

System Manual | 2014

PA8500-VES | Voice Evacuation System

PA8506-V

VES Compact System

PA8506-V

VES Compact System

Technical specifications

Rated.output.power.with.230V

.power.supply

250.W.RMS.–.with.two.250W.amplifiers.for.a.dual.

voice.and.music.channel

Rated.output.power.with.24V

.power.supply

160.W.RMS.–.with.two.160W.amplifiers.([email protected]

)

N°.of.output.zones

6.zones.with.a.redundant.double.line.(A.+.B)

Display

3”.backlit.display,.128x64.pixels.

Inputs
USB-EXT.

USB input powered via the front panel –Type A socket

Emergency microphone

•.Sensitivity./.Impedance
•.Frequency.response./.S/N.ratio

Balanced.XLR-F.on.front.panel
Signal.level.20.mV./.10.k

60.÷.20.000.Hz./.72.dB

IN.1

Socket (MIC.)

•.Sensitivity./.Impedance
•.Frequency.response./.S/N.ratio

Programmable modes: ON / OFF / Precedence / Mix con IN.2

Balanced.XLR-F.(with.activatable.21.V.phantom.power.supply)
Signal.level.Min..3.mV.-.Max.100.mV./.1.8.k

240.÷.20.000.Hz./.63.dB

IN.2
Socket (MIC.)

•.Sensitivity./.Impedance
•.Frequency.response./.S/N.ratio

Socket (LINE)

•.Sensitivity./.Impedance
•.Frequency.response./.S/N.ratio

Programmable modes: ON/ OFF / Precedence / VOX con A.P.T.

Balanced.XLR-F.(with.activatable.21.V.phantom.power.supply)
Signal.level.Min..3.mV.-.Max.100.mV./.1,8.k

240.÷.20.000.Hz./.63.dB
Balanced.with.terminals.(HOT-COM-GND)
Signal.level.Max.1800.mV./.31.k

60.÷.20.000.Hz./.84.dB

IN.3

Socket (LINE-VOX)

•.Sensitivity./.Impedance
•.Frequency.response./.S/N.ratio

Programmable modes: ON/ OFF / VOX con A.P.T.

Balanced.with.terminals.(HOT-COM-GND)
Signal.level.Max.3600.mV./.3.k

90.÷.20.000.Hz./.86.dB

AUX

•.Sensitivity./.Impedance
•.Frequency.response./.S/N.ratio

rCA stereo socket for source of sound (BGM) - Conversion to mono

Signal.level.Max.1800.mV./.31.k

60.÷.20.000.Hz./.84.dB

Paging units

•.Sensitivity./.Impedance
•.Frequency.response./.S/N.ratio

2 rJ45 sockets per unit (PA) - PMB106/PMB112 and ACIO8136 ranges

Signal.level.Max.1400.mV./.85.k

60.÷.20.000.Hz./.83.dB

EMErGENCy UNITS

rJ45 for connection and dedicated emergency microphone station.

EXT. AMP.IN

External amplifier input with terminals 0 - 70 - 100V (max. 250W rMS).

Outputs
Constant voltage outputs

•.Load.impedance.(PA8506-V.only)
•.Load.impedance.(with.250.W.external.amplifier)

6 zones for dual-line /A/B) 100 V lines - Tot. 12 pairs of terminals, 2.5 mm

Min..40

for.total.group.of.zones.1.to.6..

Min..40

for.total.group.of.zones.1.to.3../.Min..40

for.total.group.of.zones.4.to.6

External amplifier

•.Sensitivity./.Impedance
•.Frequency.response./.S/N.ratio

Output for external amplifier with balanced XLr-M socket and level 0 dBV

1.V./.500.

40.÷.20.000.Hz./.84.dB

Monitor BF OUT

•.Output./.Impedance

Loudspeaker built into front panel 1 W / 8

Rear.output.with.terminals.(HOT-GND).-.1.V./.400.

Connections to external peripheral units
remote links

•.Sensitivity./.Impedance.of.

voice.–.music.channels

•.Output./.Impedance.of.

voice.–.music.channels

rJ45 for connection to secondary PA8506-V unit (slave).

Signal.level.Max.3600.mV./.3.k

1.V./.400.

Emergency controls

•.CONTROL.INPUTS
•.CONTROL.OUTPUTS

Programmable to

normally open or normally closed states.

8.inputs.with.diagnostics..Terminals.and.service.power.supply:.24.VDC.
6.open-drain.outputs,.max.200mA..Terminals.and.service.power.supply:.24.VDC.,
2.relays.for.signalling.emergencies.and.failures,.N.O-N.C..terminals.-.Exchange

Precedence IN 1 - IN 2

Precedence input and terminals with 12 VdC power supply.

LAN

LAN rJ45 socket for TCP/IP connection to web server.

General information

230V

power.supply

[email protected]

Typical consumption with voice signal

Consumption with no signal (test tone only)

230.V

50/60.Hz.±10%

(500W.System).P.=.650W/800VA.-.(250W.System).P.=.370W/480VA

(500W.System).P.=.160W/200VA.-.(250W.System).P.=.90W/120VA

P.=.30W/45VA

24V

.secondary.power.supply

Max.consumption.@24V

.(@28Vcc)

Typical.consumption.with.voice.signal.@24V

.(@28V

)

Consumption with no signal (test tone only)

24.V

.(min.22V

.÷.max.28V

)

500W.System.=17A.(21A).-.250W.System.=9A.(11A)

500W.System.=4,3A.(5A).-.250W.System.=.2,2A.(2,5A)

0,8A

Operating.environmental.conditions

Temperature:.+5°C.to.+40°C.....Relative.humidity:.25%-75%.non-condensing

Mounting

Optional.AC8506.brackets.for.mounting.in.19”.rack.(height:.3U.+.1U.support.brackets).

Size.(W.x.H.x.D)./.Size,.packaged.(W.x.H.x.D)

439.x.387.x.132.mm./.535.x.470.x.225.mm

Net.weight./.Gross.weight

20,5.kg./.22.kg

Содержание PA8506-V





































































Результаты поиска

Содержание PA8506-V

Отзывы:

Paso PA8506-V, Инструкция по эксплуатации, Страница: 65 / 68

Результаты поиска

Содержание PA8506-V

Отзывы: