Paso PA8506-V Скачать руководство пользователя страница 38

Страница: 38 / 68

PA8506-V

VES Compact System

PA8500-VES | Voice Evacuation System

System Manual | 2014

8.5.1.3 LOUdSPK. LINE FAULT

diagnostics of line speaker units

From.the.FAULTS.panel.(point.8.5.1),.press.numerical.key.1.and.access.the.

panel.for.viewing.the.loudspeaker.line.diagnostics:.the.diagnostics.for.each.

output.zone.are.shown.as.indicated.in.the.following.table.

Press.ESC.to.return.to.the.FAULTS.panel.

Label Part being

diagnosed

Signalling

Cause

Action required

No.failure

Zone.1 Loudspeaker.lines

Zone.1

Short.A

Short.circuit.on.the.line.connected.to.

output.A.

Eliminate.the.short.circuit.and.

carry.out.a.MANUAL.RESET.of.

the.FAILURE.signal.(from.the.

OPERATOR.menu)

Zone.2 Loudspeaker.lines

Zone.2

Short.B

Short.circuit.on.the.line.connected.to.

output.B.

Zone.3 Loudspeaker.lines

Zone.3

Short.A+B

Short.circuit.on.both.lines.of.the.zone..

(Note.1)

Zone.4

Loudspeaker.lines

Zone.4

Impedance.Hi

Impedance.level.higher.than.acquired.

value.detected,.beyond.the.tolerance.set.

during.configuration.(Note.2)

Check.the.connections.of.the.speaker.

units.and.if.necessary.repeat.the.line.

acquisition. procedure. (ACQUIRE.

IMPEDANCE)

Zone.5

Loudspeaker.lines

Zone.5

Impedance.Low Impedance.level.lower.than.acquired.value.

detected,.beyond.the.tolerance.set.during.

configuration.(Note.2)

Zone.6 Loudspeaker.lines

Zone.6

Res..imp..Hi

Failure.(“Impedance.Hi”.signal).cleared

Access. the. Report. >. FAULTS. panel.

from.the.OPERATOR.menu.and.carry.

out.a.MANUAL.RESET.of.the.FAILURE.

signal

Res..imp..Low

Failure.(“Impedance.Low”.signal).cleared

Tab..8.5.1.3

Note 1:

It.may.happen.that.an.occasional.short.circuit.of.a.single.line.does.not.give.the.diagnostic.system.sufficient.time.to.identify.the.line.that.has.failed..

In.this.case,.the.message.“Short.A+B”.may.be.displayed.

Note 2:

.“Impedance.Hi”.and.“Impedance.Low”.failures.are.not.reported.if.the.tolerance.is.set.at.a.higher.level.than.the.measured.variation.of.the.

impedance.or.if.the.test.is.disabled..For.details.concerning.programming,.see.the.

SET TOLErANCE

.panel.(point.8.7.2).

8.5.1.4 VOICE ALArMS FAULT

diagnosing faults of the VES emergency sources

From. the. FAULT. panel. (point. 8.5.1),. press. numerical. key. 2. and. access.

the.panel.for.viewing.the.diagnostics.of.the.VES.emergency.sources..The.

diagnostic.state.of.each.item.monitored.is.reported,.as.shown.in.the.following.

table.

For.some.items.of.equipment.it.may.be.necessary.to.access.the.sub-panel,.

by.pressing.the.corresponding.numbered.key.

Press.ESC.to.return.to.the.panel.FAULTS.

Содержание PA8506-V





































































Результаты поиска

Содержание PA8506-V

Отзывы:

Paso PA8506-V, Инструкция по эксплуатации, Страница: 38 / 68

Результаты поиска

Содержание PA8506-V

Отзывы: