Paso PA8506-V Скачать руководство пользователя страница 44

Страница: 44 / 68

PA8506-V

VES Compact System

PA8500-VES | Voice Evacuation System

System Manual | 2014

8.5.2

IMP. rEAL TIME

real-time line impedance

Panel.for.checking.the.impedance.values.measured.in.real.time,.and.percentage.

variations. from. the. value. stored. during. start-up,. using. the. “Line. impedance.

acquisition”.procedure..The.6.zones.are.listed,.with.their.impedances,.measured.in.

Ohms..The.measure.indicated.is.referred.to.both.lines.-.A.and.B.-.connected.to.the.

zone.output..If.the.percentage.of.variation.exceeds.the.level.of.tolerance.set.at.the.

time.of.configuring.the.system,.a.“LOUDSPK.LINE.FAULT”.due.to.an.excessively.

high.or.low.impedance.(Impedance.Hi.or.Impedance.Low).will.be.signalled.
Press.ESC.to.return.to.the.INSPECTION.panel.

8.5.3

CHECK MESSAGES

diagnosis of stored messages

Panel.for.checking.all.stored.data.for.each.of.the.emergency.messages..Referring.to.

the.two.messages.EVAC.and.ALERT,.it.shows.the.checksum.data.in.alphanumeric.

format.(see.example.in.the.figure)..A.different.checksum.data.is.generated.when.the.

new.message.is.stored.
Press.ESC.to.return.to.the.INSPECTION.panel.

Note:

if several input contacts are activated simultaneously, with

different programming of the messages in relation to the zones, for

each zone output the system will enable the event with the highest

priority (see table). The CONTROL INPUT STATUS panel will

therefore show the zone outputs as configured following enabling of

all the active contacts.

Maximum.priority

General.reset.of.messages.(RESET)

High.priority

Pre-recorded.Evacuation.message.(EVAC)

Low.priority

Pre-recorded.Alert.message.(ALERT)

Minimum.priority

No.event.(NONE)

8.5.4

CONTrOL INPUTS STATUS

Status of the local input contacts

Panel.for.viewing.the.status.of.the.local.input.contacts.(CONTROL.INPUTS)..A.list.of.

the.input.contacts.activated.by.external.peripheral.units.is.provided..The.CONTROL.

INPUT. STATUS.panel. shows. the. active. inputs,. both. if. no. events. are. associated.

with.them.and.if.an.output.message.event.is.associated.with.them..In.the.event.of.

activation. of. a. programmed. CONTROL. INPUT,. the. PA8506-V. system. will. trigger.

an.“Alarm.Condition”.(VOICE.ALARM),.cause.the.ALARM.LED.to.light.up.and.the.

CONTROL. INPUT. STATUS. panel. to. be. displayed. automatically..The. display. will.

show. a. list. of. all. the. active. inputs. (whether. programmed. or. otherwise). and. will.

indicate.the.type.of.pre-recorded.message.being.output.to.each.zone..In.the.event.

of.an.active.input.contact.programmed.for.a.GENERAL.RESET,.the.ALARM.LED.

will.be.extinguished.

For.further.information.concerning.programming,.consult.point.8.6.1,.OPERATOR/Set>.CONTROL.INPUTS...For.details.on.activity.in.

the.“Voice.Alarm.Condition”,.consult.point.8.8.Automatic.Emergency.–.Voice.Alarm.Condition.

Press.ESC.to.return.to.the.panel.INSPECTION.

8.5.5

INdICATOrS TEST

Check of the functionality of the visual and audio signal elements

Panel. for. checking. speaker. functionality. (BEEP),. display. and. operating. emergency. LED. indicators..All. LEDs. on. the. front. panel. (excluding.

‘ON’.LED).and.the.EMERGENCY.key.LED.are.flashing..Horizontal.bar.scrolls.on.the.display.and.beep.warning.tone.are.ON...The.functionality.

of.the.built-in.speaker,.all.LEDs.and.all.the.display.pixels.are.checked..Please.contact.Support.in.case.of.failure..Press.ESC.to.return.to.the.

INSPECTION.panel.

Содержание PA8506-V





































































Результаты поиска

Содержание PA8506-V

Отзывы:

Paso PA8506-V, Инструкция по эксплуатации, Страница: 44 / 68

Результаты поиска

Содержание PA8506-V

Отзывы: