Paso PA8506-V Скачать руководство пользователя страница 21

Страница: 21 / 68

System Manual | 2014

PA8500-VES | Voice Evacuation System

PA8506-V

VES Compact System

r2.

Terminals for external 24 VdC power supply

Terminals.for.connecting.the.auxiliary.24.VDC.power.supply..This.is.not.used.when.the.230.VAC.mains.power.supply.is.available...The.

cables.used.must.have.a.suitable.cross-section.based.on.the.data.supplied.by.the.manufacturer.of.the.power.supply.unit..Consumption.

of.the.system.with.a.full.load.is.600.W..The.input.is.protected.against.inversion.of.the.poles..Consult.the.“Power.supply.and.earthing”.and.

“Safety.Notes”.sections.for.details.about.safety.

r3.

MONITOr BF OUT

Output.for.the.audio.signal.of.the.monitoring./beep.loudspeaker..It.can.be.used.to.remotise.the.tone.of.the.acoustic.signal.indicating.a.Fault.

Condition..Two.screw-down.terminals.for.leads.to.be.stripped.with.a.balanced.signal.

r4.

EXT. AMP OUT

Output.for.the.audio.signal.of.an.external.amplifier..It.enables.the.system.to.be.expanded.by.increasing.the.available.power.up.to.a.total.of.

500.W..Use.a.power.booster.with.an.output.of.up.to.a.maximum.of.250.W/rms..XLR-M.plug.with.a.balanced.signal.at.line.level.for.connecting.

a.balanced.shielded.microphone.cable..If.the.24.VDC.emergency.auxiliary.power.supply.is.connected.to.the.amplifier.and.to.the.PA8506-V,.

it.is.recommended.that.the.shield.of.the.cable.be.connected.only.on.the.side.of.the.socket.on.the.amplifier,.leaving.it.disconnected.from.

the.connector.on.the.side.of.the.PA8506-V.socket.

r5.

EMErGENCy UNITS

Input.for.connecting.remote.emergency.microphone.stations..Use.only.the.PASO.PMB132-V.and/or.PMB132/12-V.microphone.stations..

RJ45.socket.for.connection.with.Cat..5e.SF/UTP.cable.with.a.shielding.braid.and.shielded.STP.connector.(for.details.of.the.connection,.

consult.the.manual.of.the.PASO.11/716.stations).

r6.

rEMOTE LINK

Output.for.connection.to.the.remote.PA8506-V.unit..This.can.be.done.in.order.to.expand.the.system,.configuring.it.as.a.12-zone.system,.

by.connecting.two.PA8506-V.units.to.one.another..The.maximum.length.of.the.connection.is.1.km..RJ45.socket.for.connection.with.Cat..

5e.SF/UTP.cable.with.shielding.braid.and.shielded.STP.connector.

r7.

PAGING UNITS

Input.for.connecting.paging.microphone.stations.(PMB106-G,.PMB112-G).for.broadcasting.functions..It.is.possible.to.connect.up.to.a.total.of.16.

Paging.Units..RJ45.sockets.(2.off).for.connection.with.Cat..5e.SF/UTP.cable.with.shielding.braiding.and.shielded.STP.connector..The.connection.

with.the.Paging.Units.must.be.of.the.daisy-chain.type..The.two.connecting.lines.can.reach.a.total.length.between.them.of.up.to.1.km.

r8.

IN. 3 – LINE

Balanced.INPUT.3.for.an.external.line,.dedicated.specifically.to.the.voice.channel,.enabling.easy.interfacing.with.automatic.message.

generators.or.with.PABX’s.having.suitable.paging.audio.outputs..To.programme.this.operating.mode,.the.input.must.be.enabled.directly.as.

a.Voice.source,.or.for.automatic.VOX.activation,.with.an.adjustable.activation.threshold.and.release.time..The.signal.will.be.played.out.to.

the.group.of.zones.indicated.in.the.list.and.on.the.basis.of.the.priorities.set,.for.which.there.are.7.levels..The.socket.with.3.terminals,.HOT.

–.COM.–.GND..for.wires.to.be.stripped,.enables.a.balanced.signal.of.up.to.3.6.to.be.connected,.using.shielded.balanced.microphone.cable..

For.details.concerning.the.settings.of.the.IN..3.input,.refer.to.the.instructions.in.the.AUDIO.SETTING.>.INPUT.3.menu.

r9.

LAN

Socket.for.connecting.an.Ethernet.10/100.Local.Area.Network.using.the.TCP/IP.protocol..Provisions.for.a.Web.Server.for.access.to.the.

advanced.functions.of.the.system.in.the.Remote.Servicing.mode..RJ45.socket.for.connection.using.CAT..5e.UTP.cable.

r10.

IN. 2 – MIC. / LINE e MOrSETTO dI PrECEdENZA

INPUT.2.is.a.balanced.input.for.a.microphone.or.an.external.source,.programmable.as.a.Music.or.Voice.source..Use.the.MIC.input.to.connect.

dynamic.or.electret.microphones,.enabling.the.phantom.power.supply.or,.as.an.alternative,.the.input.on.the.terminal.strip.for.sources.at.line.

level.such.as.mixers.or.pre-amplified.microphone.stations..The.input.can.be.set.in.many.different.ways,.depending.on.how.the.operating.

mode.is.programmed:..

-. enabled.directly.as.a.Music.or.Voice.source,.

-. mixed.with.input.1.(IN..1)..

-. as.a.Voice.source.enabled.by.the.precedence.contact.(PREC.),.with.a.CHIME.that.can.be.activated/de-activated..

-. as.a.voice.source.for.automatic.VOX.activation.with.adjustment.of.the.activation.threshold.and.of.the.release.time.and.the.possibility.of..

. an.activatable/de-activatable.CHIME.

When.used.as.a.voice.source,.the.priority.can.be.set.with.7.different.levels,.and.the.group.of.paging.zones.can.be.selected..

Do.not.use.simultaneously.the.MIC..and.LINE.inputs.of.the.IN..2.input.but:

-...the.XLR.F.socket.for.connecting.a.balanced.signal.of.up.to.100.mV,.or

-...the.socket.with.3.terminals,.HOT-COM-GND,.for.stripped.wire,.for.connection.of.a.balanced.signal.of.up.to.1.8.V.

In.both.cases,.use.shielded.balanced.microphone.cable..For.details.concerning.the.settings.of.the.IN..2.input,.refer.to.the.information.

shown.in.the.Music.menu.and.under.AUDIO.SETTINGS.>.INPUT.2.and.CHIME..

PrECEdENCE TErMINAL STrIP

Terminal.strip.for.connecting.the.precedence.contact.to.the.current.music.source,.for.activation.of.the.IN..1.or.IN..2..inputs.and.of.the.CHIME,.

if.enabled..The.precedence.function.can.be.used.in.either.of.the.3.following.ways:

-. IN..1.input.only.connected.to.the.precedence.contact.and.with.the.IN..1.input.set.in.the.“Precedence”.mode

-. IN..2.input.only.connected.to.the.precedence.contact.and.with.the.IN..2.input.set.in.the.“Precedence”.mode

-. IN..1.and.IN..2.inputs.both.connected.to.the.precedence.contacts,.with.the.IN..2.input.set.in.the.“Precedence”.mode.and.the.IN..1.input.set.

in.the.“Mixing.on.IN.2”.mode.

For.details.about.the.precedence.settings,.refer.to.the.indications.shown.on.the.INPUT.1.and.INPUT.2.panels.and.to.the.AUDIO.SETTING.

menu..Activation.is.carried.out.keeping.the.+12.V.terminal.connected.to.the.PR..terminal,.by.closing.a.dry.contact.or.connecting.the.available.

precedence.contact.to.PASO.table-top.microphones.of.the.B701,.B711.or.B53.ranges.

Содержание PA8506-V





































































Результаты поиска

Содержание PA8506-V

Отзывы:

Paso PA8506-V, Инструкция по эксплуатации, Страница: 21 / 68

Результаты поиска

Содержание PA8506-V

Отзывы: