Panasonic Workio DP-C401, Руководство по обслуживанию

Страница: 56 / 548

2-31
Chapter 2 Maintenance
ADJ3. 1. 3 DADF Non-standard Document Custom Registration Function
Purpose Document sizes other than DADF detectable document size (non-standard size) are
registered and transported as standard document size. Hence, special document sizes specified by
a user can be transported.
[Overview]
Document size detection is performed based on custom-registered data and the DADF process is
performed by making the specified document sizes as scanning size. Only one custom-registration
is available. If the registered data is valid, document size detection is performed, placing priority
over the existing detection table.
Preparation:
1. Borrow the non-standard document to be custom- registered from the customer.
2. Check which direction (LEF or SEF) the customer wants to run in.
3. Check which paper size and direction the customer wants to make copies of.
4. Check the length of Fast Scan direction (X) and Slow Scan direction (Y) in Scale etc of the
borrowed document accurately and write them down.
Adjustment
Procedure
1. Enter the UI Diag and change the NVM Read/Write.
2. Set the following NVM Data to be custom-registered detection.
For the X and Y obtained at Preparation:
• Set the 710-024 data to 1. (Have the custom-registration valid.)
• Store (X+10) x 10 in the 710-018 data. (Set the Fast Scan direction Max.value)
• Store (X-10) x 10 in the 710-019 data. (Set the Fast Scan direction Min.value)
• Store (Y+10) x 10 in the 710-020 data. (Set the Slow scan direction Max.value)
• Store (Y-10) x 10 in the 710-021 data. (Set the Slow scan direction Min.value)
• Enter the 710-022 data. (Select the paper size that the customer specifies from the
table below, and enter it.)
• Enter the 710-023 data. (Select the paper direction that the customer specifies from the
table below, and enter it.)
Enter the 710-023 data. (Select the paper direction that the customer specifies from the
table below, and enter it.)
Enter the 710-023 data. (Select the paper direction that the customer specifies from the
table below, and enter it.)
The following are information regarding the NVM entered above.
3. Check the settings of the NVM Data again.
Set Fast Scan direction max.value - Fast Scan direction min. value are 200 or below.
(within 20mm)
Set slow scan direction max.value - slow scan direction min. value are 200 or below.
(within 20mm)
The following sizes cannot be entered in order to prevent mis-detection of the size sensor.
• Fast Scan direction Max.:2190~2290
• Fast Scan direction Min.:2810~2910
Chain-Link Indicated Data Name Remarks
710-018 Fast Scan direction Max.value
Note1) Setup Range=1297~3070 Set by 0.1mm (initial
value=2970)
710-019 Fast Scan direction Min.value
Note1) Setup Range=1297~3070 Set by 0.1mm (initial
value=2970)
710-020 Slow Scan direction Max.value
Note2) Setup Range=1297~4418 Set by 0.1mm (initial
value=2100)
710-021 Slow Scan direction Min.value
Note2) Setup Range=1297~4418 Set by 0.1mm (initial
value=2100)
710-022 Specified paper code for
custom-registration 03: 5.5 x 8.5"
04: A5
05: B5
08: A4
09: 8 x 10"
10: 8.5 x 11"
11; 8.5 x 12.4"
12: 8.5 x 13"
13: 8.5 x 14"
14: B4
15: A3
16: 11 x 17"
20: ILLEGAL SIZE (Initial Value=08)
710-023 Feed direction of document size 0: LEF, 1:SEF (Initial Value=0)
710-024 DADF Document Size Detec-
tion Table Custom Registration
Specification Document Size Detection Table Custom
Registration Specification is not used: 0
Document Size Detection Table Custom
Registration Specification is used: 1
(Initial Value=0)