Ormazabal velatia cgmcosmos Скачать руководство пользователя

Страница: 83 / 120

5.10.1. Selection of recommended fuses

The fuses recommended for use in the fuse protection

functional units are defi ned according to the tests carried

out. The following

table shows the recommended fuse ratings according to

the U

transf.

ratio:

network

[kV]

cubicle

[kV]

fuse

[kV]

Rated power of the transformer

WITHOUT OVERLOAD

[kVA]

100 125

160 200 250

315

400

500

630

800

1000 1250 1600 2000

Rated fuse current (A) IEC 60282-1

6/12

6.3

31.5

100

160

200

13.5

10/24

6.3 6.3 10

31.5

100

10/24

6.3 6.3 10

31.5

10/24

6.3 6.3 6.3

31.5

125

Table 5.1.

Recommended fuse calibres

Fuses recommended: SIBA brand with medium type

striker, conforming to IEC 60282-1 (Low loss fuses).

The values for combined fuses, in accordance with

IEC 62271-105, are greyed.

The fuse-switch assembly has been temperature-rise

tested under normal service conditions according to

IEC 62271-1.

A fuse-holder carriage adapted for 292 mm 6/12 kV

fuses is available.

For ratings not marked in bold the measurement is

442 mm.

If any of the fuses blows, we recommend changing all

three.

For overload conditions in the transformer or use of

other brands of fuse, please check with

Ormazabal

For the auxiliary services function, the recommended

fuse is "Back up" type 10/24 kV, 442 mm, calibre 2 A.

Transfer current according to IEC 62271-105:

fuse

[kV]

cubicle

[kV]

transfer

[A]

2300

1600

Table 5.2.

Transfer current

IG-078-EN version 12; 23/04/2020

General Instructions

cgmcosmos

: Medium-voltage cubicles with full insulation

in SF

gas up to 24 kV in accordance with IEC Standard

Recommended sequence of operations

Содержание velatia cgmcosmos

























































































































Результаты поиска

Содержание velatia cgmcosmos

Отзывы:

Похожие инструкции для velatia cgmcosmos

Бренды по названию

Популярные бренды

Ormazabal velatia cgmcosmos, Общее руководство по инструкции

Результаты поиска

Содержание velatia cgmcosmos

Отзывы:

Похожие инструкции для velatia cgmcosmos

Бренды по названию

Популярные бренды