Ormazabal velatia cgmcosmos Скачать руководство пользователя

Страница: 50 / 120

5.2. Live voltage indicator

[12]

See section “5.3. Phase concordance check”.

Ormazabal

has two live voltage indication options:

1. ekor

.vpis unit for detecting voltage, designed in

accordance with Standard IEC 62271-206. Therefore,

the "live voltage" indication is displayed when the line-

to-earth voltage is equal to or greater than 45 % of the

rated voltage and is not visible when the line-to-earth

voltage is less than 10 % of the rated voltage.

The

ekor

.ivds unit for detecting voltage is designed in

accordance with Standard IEC 61243-5. Therefore, the

"live voltage" detection is displayed when the line-

to-earth voltage is between 45 % and 120 % of the

rated voltage and is not visible when the line-to-earth

voltage is less than 10% of the rated voltage.

Both units provide a clear visual indication for the user,

without needing an auxiliary power supply for operation.

For each of the three phases, the presence of voltage is

indicated by intermittent flashing of the indicators.

The voltage detector has the following displays:

L1, L2, L3 signal each of the indicator phases. The

numbering corresponds to the order of the phases,

from left to right, seen from the front of the cubicle.

Each phase has a test point for checking the phase

concordance between cubicles.

Live voltage indicator.

The flashing light indicates the presence of voltage in

this phase.

Phase test points.
Each phase has a test point for checking the phase

concordance between cubicles.

Earth test point.

This is only used for comparing the phases.

Figure 5.3.

Live voltage indicator unit

The purpose of the test points for the three phases and

earth is to make it easier to check the phase concordance

[12]

between cubicles.

Ormazabal

's specific phase comparator

ekor

.spc can be used to do this.

With the

ekor

.vpis, if the indicators do not light up, use

other means to check that there is no voltage.

IG-078-EN version 12; 23/04/2020

Recommended sequence of operations

General Instructions

cgmcosmos

: Medium-voltage cubicles with full insulation

in SF

gas up to 24 kV in accordance with IEC Standard

Содержание velatia cgmcosmos

























































































































Результаты поиска

Содержание velatia cgmcosmos

Отзывы:

Похожие инструкции для velatia cgmcosmos

Бренды по названию

Популярные бренды

Ormazabal velatia cgmcosmos, Общее руководство по инструкции

Результаты поиска

Содержание velatia cgmcosmos

Отзывы:

Похожие инструкции для velatia cgmcosmos

Бренды по названию

Популярные бренды