Ormazabal velatia cgmcosmos Скачать руководство пользователя

Страница: 17 / 120

3. Storage

If it needs to be stored, the equipment must be placed on

dry ground or on top of damp-proof insulating material, still

in its original packaging.

After prolonged storage, clean all the insulating parts

carefully before commissioning the equipment. The

enclosure should be cleaned with a clean, dry lint-free cloth.

Figure 3.1.

Storage

Storage must always be INDOORS, with the following

conditions recommended:

Ambient air temperature should not exceed 40 ºC

and its mean value, measured in a period of 24 hours,

should not exceed 35 ºC.

The ambient air temperature should not drop below

- 5°C. There are also cubicles with storage temperature

up to -40°C.

The switchgear must be protected from direct solar

radiation.

Altitude, both in transport and in storage, must not

exceed 2000 m.

The environmental air must not have any signifi cant

contamination from dust, smoke, corrosive and/or

infl ammable gases, vapours or salt.

The switchgear must be protected from the rain, and

the humidity conditions should be as follows:

The mean relative humidity value, measured over a

period of 24 hours, must not exceed 95%.

The mean water vapour pressure value, measured in

a period of 24 hours, must not exceed 2.2 kPa.

The mean relative humidity value, measured over a

period of one month, must not exceed 90%.

The mean water vapour pressure value, measured

over a period of one month, must not exceed

1.8 kPa.

During transport, vibrations caused by external factors

or seismic movements must be insignifi cant.

Any other conditions must be notifi ed beforehand,

since the equipment must be factory-adjusted to

the environmental pressure at the fi nal destination

or during transport. Otherwise, the pressure gauge

needle may indicate an incorrect value, even if the

equipment's internal gas pressure is correct.

IG-078-EN version 12; 23/04/2020

General Instructions

cgmcosmos

: Medium-voltage cubicles with full insulation

in SF

gas up to 24 kV in accordance with IEC Standard

Storage

Содержание velatia cgmcosmos

























































































































Результаты поиска

Содержание velatia cgmcosmos

Отзывы:

Похожие инструкции для velatia cgmcosmos

Бренды по названию

Популярные бренды

Ormazabal velatia cgmcosmos, Общее руководство по инструкции

Результаты поиска

Содержание velatia cgmcosmos

Отзывы:

Похожие инструкции для velatia cgmcosmos

Бренды по названию

Популярные бренды