Ormazabal velatia cgmcosmos Скачать руководство пользователя

Страница: 15 / 120

2. Handling and transport

[3]

Position the rear of the cubicle facing the driver, to avoid damaging the front.

Important:

During transport, the switchgear must

be perfectly seated and fixed so that it cannot move

about and possibly damage the equipment.

2.1. Lifting means

The switchgear must always be kept upright, directly on the

ground or on a pallet depending on the type of handling

involved.

One of the following methods must be used for assemblies

of up to 4

cgmcosmos

functional units:

Using a forklift truck or pallet truck.

[3]

Figure 2.1.

Lifting a

cgmcosmos

cubicle using a forklift truck

Lifting using slings or chains fixed to the lifting brackets

on the sides of the top of the cubicle. The angle of pull

should be as vertical as possible (with an angle greater

than 60º from the horizontal).

Figure 2.2.

Lifting

cgmcosmos

cubicles with chains

IG-078-EN version 12; 23/04/2020

General Instructions

cgmcosmos

: Medium-voltage cubicles with full insulation

in SF

gas up to 24 kV in accordance with IEC Standard

Handling and transport

Содержание velatia cgmcosmos

























































































































Результаты поиска

Содержание velatia cgmcosmos

Отзывы:

Похожие инструкции для velatia cgmcosmos

Бренды по названию

Популярные бренды

Ormazabal velatia cgmcosmos, Общее руководство по инструкции

Результаты поиска

Содержание velatia cgmcosmos

Отзывы:

Похожие инструкции для velatia cgmcosmos

Бренды по названию

Популярные бренды