Ormazabal velatia cgmcosmos Скачать руководство пользователя

Страница: 18 / 120

4. Installation

4.1. Unpacking the equipment

[4]

It is advisable to cut the cellophane at the rear of the cubicle or at the corner to avoid scratching the surface.

The

cgmcosmos

system switchgear is supplied as standard

protected by plastic packaging.

On receiving the equipment, check that the goods supplied

correspond to the order and associated documentation. If

this is not the case, contact

Ormazabal

immediately.

The disassembly process for the equipment is as follows:

Using a blade, cutter or similar tool, cut the cellophane

the cubicle is wrapped in.

[4]

Completely remove the cellophane.

Detach the white polystyrene corner pieces.

Unscrew the fixings between the base and the pallet.

Remove the pallet, handling the cubicle as indicated in

section 2.1.

Unpack the accessories box in the front section or on

the top of the cubicle.

Remove the self-adhesive protective plastic from the

cable compartment cover.

The self-adhesive plastic must be removed from the

cable compartment cover so that the equipment

enclosure's earth connection may have the proper

electrical continuity.

Dispose of any waste in an environmentally friendly

manner.

It is advisable to make a visual inspection of the equipment

to check whether it has suffered any damage in transit. If

damaged, contact

Ormazabal

immediately.

4.2. Positioning accessories during transport

A number of accessories are supplied with the cubicles,

located as indicated in the figures below:

Figure 4.1.

Location of accessories in transport in unifunctional

cgmcosmos

cubicles

IG-078-EN version 12; 23/04/2020

Installation

General Instructions

cgmcosmos

: Medium-voltage cubicles with full insulation

in SF

gas up to 24 kV in accordance with IEC Standard

Содержание velatia cgmcosmos

























































































































Результаты поиска

Содержание velatia cgmcosmos

Отзывы:

Похожие инструкции для velatia cgmcosmos

Бренды по названию

Популярные бренды

Ormazabal velatia cgmcosmos, Общее руководство по инструкции

Результаты поиска

Содержание velatia cgmcosmos

Отзывы:

Похожие инструкции для velatia cgmcosmos

Бренды по названию

Популярные бренды