![background image](http://html1.mh-extra.com/html/omron/sysmac-cs-series/sysmac-cs-series_reference-manual_742030817.webp)
777
Data Control Instructions
Section 3-18
At the rising edge of W 000000 (OFF to ON), SETB(532) turns ON bit 15 of
D00209 (C+9) and starts autotuning. When autotuning is completed, the cal-
culated P, I, and D constants are written to C+1, C+2, and C+3. PID control is
then restarted with the new PID constants.
PIDAT
0010
D00200
0020
000000
S
C
D
C: D00200
C+1: D00201
C+2: D00202
C+3: D00203
C+4: D00204
C+5: D00205
C+6: D00206
C+7: D00207
C+8: D00208
C+9: D00209
C+10: D00210
C+11: D00211
C+40: D00240
0
1
2
C
0
0
6
4
0
4
B
0
0
1
9
0
0
0
3
2
0
0
0
0
0
4
9
4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
W00000
SETB
D00209
#000F
Work area
Proportional band: 10.0%
Integral time: 120.0 s
Derivative time: 40.0 s
Sampling
period: 0.5 s
Reverse operation (bit 00: 0), PID constant change enable setting =
OFF (bit 01: 0), set value = manipulated variable output 50% (bit
03: 1), 2-PID parameter = 0.65 (bits 04 to 15: 000 hex)
Manipulated variable output range: 12 bits (bits 00 to 03: 4 hex),
Integral/derivative constant: time designation (bits 04 to 07: 9 hex)
Input range: 12 bits (bits 08 to 11: 4 hex),
Manipulated variable output limit control disabled (bit 12: 0)
AT Command Bit OFF (bit 15: 0),
AT Calculation Gain = 1.00 (bits 00 to 11: 000 hex)
Limit-cycle Hysteresis = 0.20%
PID starting integral manipulated variable
designation = start from same integral
manipulated value as manipulated variable
output designation (bit 14: 0 and bit 13: 0)
Parameters
PV:
CIO 0010
MV output: CIO 0020
to
PID calculation
Set value: 300
CIO 000000
W000000
PV
SV
MV
PID control
PID control
AT executing
PID control starts.
Calculated PID
constants are set.
Bit 15 of
D00209
Time
Time
Содержание SYSMAC CS Series
