OcÃ© CS9360 Скачать руководство пользователя страница 9

Страница: 9 / 134

CS9350 OPERATION MANUAL

1-9

Chapter 1 Safety

instructions

This chapter explains the installation of this printer, warning terms that operators need to know, caution
items and warning labels on the printer main unit.

WARNING



When installing and operating this printer, be sure to follow the directions and warnings in
this book.

1.1

Types and meanings of warnings

The warnings in the Operation Manual and the warning labels attached to the printer are categorized into
three stages.

Understand the meanings of the following warning terms and follow the contents (instructions) in this
manual.

Warning

Meaning

Used for dangerous situations where death or serious injury may be caused.

Used for dangerous situations that may cause slight or medium injury, or when all or
parts of products are damaged.

Used for special cautions and for information that needs to be emphasized.

WARNING

CAUTION

NOTE

Содержание CS9360







































































































































Результаты поиска

Содержание CS9360

Отзывы:

Похожие инструкции для CS9360

Бренды по названию

Популярные бренды

OcÃ© CS9360, Руководство по эксплуатации

Результаты поиска

Содержание CS9360

Отзывы:

Похожие инструкции для CS9360

Бренды по названию

Популярные бренды