OcÃ© CS9360 Скачать руководство пользователя страница 10

Страница: 10 / 134

CS9350 OPERATION MANUAL

1-10

1.2 Important

safety

instructions

Do not install this printer in the following places.

It may cause an injury if the printer falls down.
• On a shaky stand
• Slanting location
• Places where vibration of other machines etc. is transmitted

Do not step on this printer or place heavy things on top of it.

It may cause an injury if the printer falls down.

Do not block the vent by covering the printer with cloths, such as a blanket or tablecloth.

If the vent is blocked, heat may accumulate inside the printer and it may cause fire.

Do not install the printer where it is humid or dusty.

It could lead to an electric shock and fire.

Do not use a damaged power cable.

It could lead to an electric shock and fire.

Do not pull out or insert the power plug with a wet hand.

This could lead to an electric shock.

Do not connect an earth wire to the following places.
• Gas pipes

There is a possibility of ignition and explosion.

• Earth wire of telephone cables and lightning rods

Heavy current might flow whenever lightning strikes.

• Water pipe and faucet

The earth might not work if a plastic pipe is connected in the middle of the metal pipe.

Do not insert or drop metal or flammable objects into the printer through openings such as a vent.

It could lead to an electric shock or fire.

Do not spill flammable liquid on the platen.

This could lead to a fire.

Do not place any combustible materials on the platen while the heater is working.

There may be a risk of fire.

If foreign substances or liquids such as water entered the printer, do not use the printer as it is.

It could lead to an electric shock or fire.

Immediately switch OFF the power switch, disconnect the power plug from the electric socket, and contact your
local Océ representative.

Wire the various cords as directed in the Operation Manual.

Mistaken wiring could cause fire.

Be sure to use the specified power cable.

Using power cables other than the specified can cause an electric shock or fire.

Make sure to use only the specified power supply (AC 100 V to 120 V or AC 220 V to 240 V).

If a power supply other than the specified voltage is used, it could cause an electric shock and fire.

WARNING

Содержание CS9360







































































































































Результаты поиска

Содержание CS9360

Отзывы:

Похожие инструкции для CS9360

Бренды по названию

Популярные бренды

OcÃ© CS9360, Руководство по эксплуатации

Результаты поиска

Содержание CS9360

Отзывы:

Похожие инструкции для CS9360

Бренды по названию

Популярные бренды