OcÃ© CS9360 Скачать руководство пользователя страница 22

Страница: 22 / 134

CS9350 OPERATION MANUAL

2-22

2.2 Printer

status

2.2.1 Normal

Printing is possible when media is loaded.

The various functions for printing can be performed on the operation panel.

2.2.2

Setup menu display

Various settings regarding printing can be made from the operation panel.

The various functions for printing can be performed on the operation panel.

Display contents in the LCD monitor of the operation panel are as follows.

2.2.3 Changing

printer

status

(1) Normal

→

Setup menu display

Press [Menu] when the printer is Normal.

•

“Menu 1: Setup>” is displayed and the display shifts to the Setup menu.

NOTE



For details regarding the Setup menu, refer to “4.3 Menu setups on the operation panel”.

(2) Setup menu display

→

Normal

When the printer is at the Setup menu display, perform either of the following operations to shift the
operation panel to the Normal display.

•

Press [Cancel] or [Menu].

•

In the Setup menu, leave the keys untouched for three minutes.

NOTE



For details on Status message, refer to “7.2.1 Status messages”.

Normal

Setup Menu Display

[Menu] key

[Cancel] key

Leave the printer

as it is for 3 minutes

Содержание CS9360







































































































































Результаты поиска

Содержание CS9360

Отзывы:

Похожие инструкции для CS9360

Бренды по названию

Популярные бренды

OcÃ© CS9360, Руководство по эксплуатации

Результаты поиска

Содержание CS9360

Отзывы:

Похожие инструкции для CS9360

Бренды по названию

Популярные бренды